NewAI Part GeneratorFree to get started
FREE TOOL

SEPIC converter calculator

Enter the input range, output and load in this SEPIC converter calculator to get the duty cycle, separate or coupled inductors, coupling capacitor, MOSFET and diode ratings and output capacitor. You can also enter the parts you have chosen and see their ripple and peak currents.

Task
Examples
V
V
V
A
V

Use 0 for a synchronous rectifier.

Hz

Use the minimum from the data sheet.

%

Optional, at VIN(min) and full load. Leave blank to count only the diode drop.

Inductors
%

Peak to peak, as a share of the input current. TI suggests 20 to 40%.

V

Peak to peak.

%

Peak to peak, as a share of VIN(max). TI SNVAA43 uses 5%.

A

Optional. Use the minimum from the data sheet to see the load it can carry.

Inductance

18.1 µH

L1 = L2

Next standard value (E12)
22 µH
Duty cycle at VIN(min)
59.7 % maximum, CCM
Duty cycle at VIN(max)
47.1 % minimum, CCM
Average input current (L1)
1.48 A at VIN(min)
Average L2 current
1 A equals IOUT
Ripple per winding at VIN(min)
593 mA peak to peak
Ripple per winding at VIN(max)
779 mA peak to peak
L1 peak current
1.78 A
L2 peak current
1.39 A
Inductor saturation rating
2.13 A at least, 1.2 × higher winding
Switch voltage
27.5 V rate above 35.8 V (30% margin)
Switch peak current
3.07 A L1 peak + L2 peak
Switch RMS current
1.94 A at VIN(min)
Diode reverse voltage
27.5 V rate above 35.8 V (30% margin)
Diode average current
1 A peak 3.07 A
Diode dissipation
500 mW IOUT × Vd
Coupling capacitor Cs, minimum
1.59 µF 750 mV ripple, effective value
Cs voltage rating
15 V must exceed VIN(max)
Cs RMS current
1.22 A
Output capacitor, minimum
23.9 µF half the ripple budget
Output capacitor ESR, maximum
16.3 mΩ half the ripple budget
Output capacitor RMS current
1.22 A
Input capacitor RMS current
225 mA
CCM boundary at VIN(max)
412 mA DCM below this load

Separate inductors: L1 and L2 are assumed equal, so they carry the same ripple. A separate-inductor SEPIC has an L2 and Cs resonance that the control loop must stay clear of.

Peak currents and duty cycle across the input range
0500m11.522.533.502040608010068101214161820Input voltage (V)Current (A)Duty cycle (%)VIN(min) 9 VVIN(max) 15 V
Switch peakL1 peakL2 peakDuty cycle (%)

Operating points at the ends of the input range

QuantityAt 9 VAt 15 V
Conduction modeCCMCCM
Duty cycle59.7%47.1%
Average input current1.48 A889 mA
Ripple per winding (p-p)593 mA779 mA
L1 peak1.78 A1.28 A
L2 peak1.3 A1.39 A
Switch peak3.07 A2.67 A
CCM boundary load239 mA412 mA

How do you size the inductors and switch in a SEPIC converter design?

Start from D = (VOUT + Vd) ÷ (VIN + VOUT + Vd) at the minimum input. Choose a ripple of 20 to 40% of the input current, then L1 = L2 = VIN(min) × D ÷ (ΔIL × fs), or half that for a coupled pair. For TI’s 3 V to 5.7 V input and 3.3 V at 2.5 A and 330 kHz, D = 55.9%, L = 4.62 µH and the switch peak is 6.77 A.

SEPIC converter formulas

When the switch is on, L1 charges from the input and L2 charges from the coupling capacitor, while the output capacitor feeds the load. When it turns off, both inductors send their current through the diode to the output. These SEPIC converter equations follow TI AN-1484 and SLYT309 for continuous conduction.

D = (VOUT + Vd) ÷ (VIN + VOUT + Vd)
D
duty cycle, largest at the minimum input voltage
VOUT
output voltage
Vd
diode forward voltage (0 for a synchronous rectifier)
η
estimated total efficiency, if you have one

With an efficiency estimate, power balance and charge balance give the form below. It is the same equation when the diode is the only loss:

D = VOUT ÷ (VOUT + η × VIN)

The input current is IOUT × (VOUT + Vd) ÷ VIN, or IOUT × VOUT ÷ (η × VIN) with an efficiency estimate. The inductors are sized for a ripple of r times the input current at the minimum input. With no estimate, AN-1484 leaves the diode drop out of this target, which is the same as η = 1:

ΔIL = r × IOUT × VOUT ÷ (η × VIN(min))
ΔIL
peak-to-peak ripple in each winding
r
ripple ratio, usually 20 to 40%
fs
switching frequency (use the minimum)
L1 = L2 = VIN(min) × Dmax ÷ (ΔIL × fs)     coupled: half of that

Equal inductors see the same volt-seconds, so they carry the same ripple. The switch and the diode carry the sum of both winding peaks:

IL1(peak) = IIN + ΔIL ÷ 2     IL2(peak) = IOUT + ΔIL ÷ 2
IQ(peak) = IL1(peak) + IL2(peak)

Both the switch and the diode must withstand the input and output added together:

VQ = VD = VIN(max) + VOUT + Vd

The coupling capacitor charges to the input voltage and carries a large RMS current. The output capacitor supplies the load during the on-time:

ICs(rms) = IIN × √((1 − D) ÷ D)     ΔVCs = IOUT × Dmax ÷ (Cs × fs)
COUT ≥ IOUT × Dmax ÷ (0.5 × Vripple × fs)     ESR ≤ 0.5 × Vripple ÷ IQ(peak)

SEPIC converter design examples

Example 1: the design example in TI AN-1484, 3.0 V to 5.7 V in, 3.3 V at 2.5 A, 330 kHz

With a 0.5 V diode, Dmax = 3.8 ÷ 6.8 = 55.9% and Dmin = 40.0%. The 40% ripple target is 1.1 A, so L1 = L2 = 4.62 µH and TI picks the standard 4.7 µH. The windings peak at 3.72 A and 3.05 A, the switch at 6.77 A and 4.26 A RMS. The coupling capacitor carries 2.81 A RMS and ripples 423 mV with 10 µF. For 2% output ripple at 330 kHz, the output needs at least 128 µF and an ESR under 4.88 mΩ. The input capacitor sees 318 mA RMS.

Example 2: the coupled-inductor design in TI SLYT309, 9 V to 15 V in, 12 V at 300 mA, 1 MHz

With a 90% efficiency estimate, the 30% ripple target is 133 mA and a coupled pair needs 20.1 µH per winding, where TI chooses 22 µH. The high-side winding peaks at 511 mA and the switch at 878 mA. With a ceramic output capacitor and the whole 100 mV budget on capacitance, C is at least 1.79 µF. The switch and diode see 27.5 V.

Example 3: why L2’s ripple matters when the output is well above the input, 3 V to 12 V at 1 A

D = 80.6% and a 40% ripple is 1.6 A, so L = 3.02 µH. Both windings carry that same ripple. L2 peaks at 1.8 A, not the 1.2 A you get by scaling the ripple with L2’s own current, so size its saturation rating from the shared ripple.

Duty cycle and input current for common rails

Each cell gives the duty cycle and the input current as a multiple of the load, using a 0.5 V diode and no other losses.

VIN \ VOUT3.3 V5 V12 V24 V
3.3 V53.5%, 1.15× IOUT62.5%, 1.67× IOUT79.1%, 3.79× IOUT88.1%, 7.42× IOUT
5 V43.2%, 0.76× IOUT52.4%, 1.10× IOUT71.4%, 2.50× IOUT83.1%, 4.90× IOUT
9 V29.7%, 0.42× IOUT37.9%, 0.61× IOUT58.1%, 1.39× IOUT73.1%, 2.72× IOUT
12 V24.1%, 0.32× IOUT31.4%, 0.46× IOUT51.0%, 1.04× IOUT67.1%, 2.04× IOUT
24 V13.7%, 0.16× IOUT18.6%, 0.23× IOUT34.2%, 0.52× IOUT50.5%, 1.02× IOUT

Inductance for 1 A at 40% ripple

L = VIN(min) × Dmax ÷ (ΔIL × fs) with ΔIL = 40% of IOUT × VOUT ÷ VIN(min) and a 0.5 V diode. Divide by the output current in amperes for other loads. For other conversions, use the SEPIC calculator above.

ConversionSeparate, 300 kHzCoupled, 300 kHzSeparate, 1 MHzCoupled, 1 MHz
3 V to 3.3 V12.7 µH6.35 µH3.81 µH1.91 µH
3 V to 5 V9.71 µH4.85 µH2.91 µH1.46 µH
9 V to 12 V32.7 µH16.4 µH9.81 µH4.91 µH
12 V to 12 V51 µH25.5 µH15.3 µH7.65 µH
6 V to 12 V16.9 µH8.45 µH5.07 µH2.53 µH

What goes wrong in real circuits

The coupling capacitor is the part most often undersized: its RMS current is comparable to the output current, and ceramics lose much of their value under the input-voltage DC bias, so check the effective capacitance and the ripple-current rating together. With separate inductors, L2 and Cs form a resonance that shows up in the control-to-output response; AN-1484 sets the crossover at one sixth of the lower of that resonance and the right-half-plane zero. TI itself treats the SEPIC zero as an estimate, so leave generous margin and verify the loop on the bench. The input capacitor is less critical, because L1 keeps the input current continuous and triangular: AN-1484 asks only for the ΔIL ÷ √12 RMS rating and 10 µF or more of a good quality part, to avoid impedance interactions with the source.

This calculator assumes steady-state operation, equal L1 and L2, and a constant efficiency across the input range. Capacitor sizing assumes continuous conduction; peak and RMS currents also cover DCM. Ripple grows with input voltage while average current falls, so results are shown at both ends. Two practical warnings when you read TI’s notes directly: AN-1484 Equation 10 and SLYT309 Equation 13 multiply IQ(rms)² × RDS(on) by D again, but the RMS value already contains the duty cycle, so use IQ(rms)² × RDS(on) on its own. And AN-1484 Equation 31 computes 141 µF with 300 kHz although its design runs at 330 kHz, where the same formula gives 128 µF.

Glossary

SEPIC
Single-ended primary-inductor converter: a non-inverting DC/DC topology whose output can be above or below its input.
Coupling capacitor (Cs)
The series capacitor between the two inductors, which charges to the input voltage and blocks DC.
Coupled inductor
Two windings on one core, so the same voltages drive both and the ripple splits equally between them.
Duty cycle (D)
The fraction of each switching period that the switch is on.
Continuous conduction mode (CCM)
The sum of the winding currents stays above zero through the whole switching cycle.
Inductor ripple (ΔIL)
The peak-to-peak swing of the current in each winding during a switching cycle.

Related guides

Frequently asked questions

What is the duty cycle of a SEPIC converter?

D = (VOUT + Vd) ÷ (VIN + VOUT + Vd), worst at the minimum input voltage. TI’s example of 3.0 V in and 3.3 V out with a 0.5 V diode gives 55.9%. It is 50% when VIN = VOUT + Vd, which is why the same stage can step up or down.

Should I use separate or coupled inductors?

A coupled pair needs half the inductance for the same ripple, because the mutual inductance doubles the effective value. It also saves board space, and the L2 and Cs resonance no longer affects the frequency response (TI SLYU036). Use a pair with equal windings; TI SNVAA43 prefers 10 to 15% leakage in a SEPIC.

How do I choose the inductor ripple for a SEPIC?

TI suggests 20 to 40% of the input current at the minimum input voltage. More ripple gives a smaller inductor and faster response, but raises peak current and EMI and takes more output capacitance to meet the same output ripple.

What voltage and current does the MOSFET see in a SEPIC?

It must block VIN(max) + VOUT + Vd and carries both inductor currents while on, so its peak is IL1(peak) + IL2(peak). In the TI example that is 9.5 V and 6.77 A. TI SNVAA43 adds a 30% voltage margin.

What does the coupling capacitor need to handle?

It must be rated above VIN(max) and for an RMS current of IOUT × √((VOUT + Vd) ÷ VIN(min)), which is 2.81 A in the TI example at 2.5 A. That RMS current is large for the output power, so use ceramic or tantalum parts with a real ripple-current rating and account for DC bias.

Why use a SEPIC instead of a buck or boost?

A SEPIC keeps the output positive and can regulate it above or below the input, as a battery discharges past the output voltage. The coupling capacitor also blocks DC, which isolates the input from the output and helps with a shorted load.

Why do your peak currents differ slightly from AN-1484?

AN-1484 scales each winding’s ripple by its own DC current, but equal inductors see the same volt-seconds, so they carry the same ripple. TI’s SLYT309 and handbook use that shared ripple, and this calculator does too. In AN-1484’s example the difference is small (3.72 A against 3.8 A for L1); when VOUT is well above VIN it is not.

When does a SEPIC enter discontinuous conduction?

When the load falls below ΔIL × (1 − D), which is the point where the two winding currents sum to zero at the end of the off time. The boundary is highest at VIN(max), so check it there.

What is a SEPIC converter?

A single-ended primary-inductor converter: a non-inverting DC/DC topology whose output can be above or below its input. Energy passes through two inductors and a series coupling capacitor, which blocks DC between input and output.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.