NewAI Part GeneratorFree to get started
FREE TOOL

MOSFET power loss calculator

Put datasheet values into this MOSFET power loss calculator to get the conduction, switching and output capacitance losses in a hard-switched circuit, and the junction temperature they cause. Switching times come from your rise and fall times or, better, from the gate charge and your gate driver.

Switching times from
Examples
V
A
A

Optional: inductor ripple. The switch turns on at I − ΔI/2 and off at I + ΔI/2.

%
Hz
Ω

Use the maximum at your gate drive voltage.

×

From the datasheet graph of normalized RDS(on) against junction temperature.

s

Current rise plus voltage fall.

s

Voltage rise plus current fall.

V
C
C

Optional: preferred for the Coss loss.

F

Optional: used only when Qoss is blank.

°C/W

Junction to ambient on your board, or junction to case with a case temperature below.

°C
°C

Total MOSFET loss

672.5 mW

Conduction loss
236 mW Irms 6.5 A, RDS(on) 5.58 mΩ
Switching loss
436.5 mW on 229 mW, off 207 mW
Output capacitance loss
0 W enter Qoss to include
Junction temperature
51.9 °C 26.9 °C rise
RDS(on) at that temperature
5.576 mΩ ×1.115
RMS current
6.505 A
Gate drive power (in the driver)
60 mW not in the MOSFET total

Datasheet tr and tf are measured with the manufacturer’s gate resistor, drive and load, so they are not the overlap times in your circuit. The gate charge mode estimates them from your driver.

Gate drive power is split between the driver, the gate resistor and the MOSFET’s internal gate resistance in proportion to their resistance, so it mostly heats the driver. Body-diode conduction and reverse recovery are not included.

Loss against switching frequency (RDS(on) held at 52 °C)
01234550k100k200k500k1M2MSwitching frequency (Hz)Power (W)fs 300 kHz
TotalConductionSwitching + Coss

What is the MOSFET power dissipation formula?

P = Irms² × RDS(on)(Tj) + ½ × V × I × (ton + toff) × fs + ½ × Qoss × V × fs, and Tj = Ta + θJA × P. For an Infineon BSC010N04LSC switching 20 A at 20 V and 200 kHz with a 3 Ω gate loop, that is 150 mW conduction, 1.44 W switching and 168 mW Coss loss: 1.75 W in total and a junction near 113 °C at 50 °C/W.

MOSFET conduction loss formula and switching losses

The model follows TI SLVAEQ9 for a switch that turns on at I − ΔI/2 and off at I + ΔI/2 (a buck high side, or any PWM switch with an inductive load), with the voltage clamped at V during each edge.

Pcond = Irms² × RDS(on)(Tj)     RDS(on)(Tj) = RDS(on)(25 °C) × k125^((Tj − 25) ÷ 100)
Irms
RMS switch current, √(D × (I² + ΔI²/12))
RDS(on)(Tj)
on-resistance at the junction temperature
k125
normalized RDS(on) at 125 °C from the datasheet graph
Psw = V/2 × (I − ΔI/2) × fs × ton + V/2 × (I + ΔI/2) × fs × toff
V
switched voltage
ton, toff
turn-on and turn-off transition times (current and voltage)
fs
switching frequency

From gate charge, with a driver swinging 0 to Vdr through a total gate resistance Rg (TI SLVAEQ9 Eq. 5 for turn-on; Vishay AN608A for turn-off, where the gate discharges toward 0 V):

ton = Rg × (Qgs2 ÷ (Vdr − ½(Vpl + Vth)) + Qgd ÷ (Vdr − Vpl))     toff = Rg × (Qgs2 ÷ ½(Vpl + Vth) + Qgd ÷ Vpl)
PCoss = ½ × Qoss × V × fs     Pgate = Qg × Vdr × fs     Tj = Ta + θ × (Pcond + Psw + PCoss)
Qoss
output charge at a VDS close to V
Qg
total gate charge at the drive voltage Vdr
θ
thermal resistance junction to ambient (or to case, with Ta the case temperature)

Qgd is measured at a test VDS; when you enter it, Qgd is scaled by V ÷ VDS(test) as in Vishay AN608A. TI SLVAEQ9 writes the temperature rise of RDS(on) as a factor (1 + δ) in its Eq. 7. The calculator takes that factor from the datasheet’s normalized curve, interpolated as an exponential through its value at 125 °C; on the BSC010N04LSC curve (Diagram 9 of the datasheet) that stays within about 3 % from −40 to 150 °C. The exponential is the law in Infineon’s application note by Graovac, Pürschel and Kiep, RDS(on)(Tj) = RDS(on)max(25 °C) × (1 + α/100)^(Tj − 25), which also starts from the maximum value at 25 °C and takes α from two points on the datasheet curve.

How to calculate MOSFET power dissipation: worked examples

Example 1: Infineon BSC010N04LSC at 20 V, 20 A, 200 kHz

Datasheet (typical): Qgs 16 nC and Qg(th) 11 nC, so Qgs2 = 5 nC; Qgd 15 nC and Qoss 84 nC at 20 V; plateau 2.4 V; VGS(th) 1.2 to 2.0 V (1.6 V used); RDS(on) 1.05 mΩ maximum at 10 V; θJA 50 °C/W on 6 cm² of copper. With 10 V drive and 3 Ω in the gate loop, ton = 7.8 ns (plateau current 2.53 A) and toff = 26.2 ns (only 800 mA). At 25 % duty and 4 A of ripple, Irms = 10 A.

Switching loss is 1.44 W, Coss loss 168 mW and conduction 150 mW at the solved Tj = 112.7 °C (RDS(on) 1.5 mΩ). Total: 1.75 W. The slow turn-off dominates: a driver with a stronger pull-down, or a lower gate resistance, cuts it directly.

Example 2: 12 V to 5 V buck high side at 500 kHz

5 A output with 1.5 A ripple, D = 42 %, a 10 mΩ MOSFET and transition times of 8 ns on and 6 ns off. Conduction 122 mW, switching 205 mW, total 327 mW; at 60 °C/W and 40 °C ambient the junction settles at 60 °C. Gate drive adds 25 mW in the controller.

Example 3: 24 V motor PWM at 20 kHz

8 A at 50 % duty through an 8 mΩ MOSFET whose RDS(on) is 1.6× at 125 °C. Conduction is 301 mW at Tj = 60 °C (RDS(on) has already risen to 9.42 mΩ), against 191 mW of switching loss even with 60 ns and 40 ns edges. At low frequency, pick the part for RDS(on).

MOSFET loss against switching frequency

Example 1 (BSC010N04LSC, 20 V, 20 A, 25 % duty, 3 Ω gate loop, 50 °C/W). Conduction loss changes only through Tj.

fsConductionSwitchingCossTotalTj
50 kHz117 mW359 mW42 mW518 mW51 °C
100 kHz127 mW718 mW84 mW929 mW71 °C
200 kHz150 mW1.44 W168 mW1.75 W113 °C
300 kHz178 mW2.15 W252 mW2.58 Wover the 150 °C limit
500 kHz250 mW3.59 W420 mW4.26 Wover the 150 °C limit
1 MHz605 mW7.18 W840 mW8.62 Wover the 150 °C limit

RDS(on) multiplier against junction temperature

RDS(on)(Tj) ÷ RDS(on)(25 °C) from the exponential model for four datasheet curves, labeled by their value at 125 °C. Read your part’s curve and pick the closest column.

Tjk125 = 1.4 (α 0.34 %/K)k125 = 1.5 (α 0.41 %/K)k125 = 1.7 (α 0.53 %/K)k125 = 2 (α 0.70 %/K)
25 °C×1.00×1.00×1.00×1.00
50 °C×1.09×1.11×1.14×1.19
75 °C×1.18×1.22×1.30×1.41
100 °C×1.29×1.36×1.49×1.68
125 °C×1.40×1.50×1.70×2.00
150 °C×1.52×1.66×1.94×2.38
175 °C×1.66×1.84×2.22×2.83

Limits of the model

The switching estimate in this MOSFET loss calculator assumes linear current and voltage ramps and ignores the common source inductance of the package and layout, which slows both edges and raises switching loss (TI SLPA009A quantifies it); use a Kelvin source pin and a tight gate loop. Body-diode conduction during dead time and reverse recovery charge (Qrr × V × fs) are not included and matter for the low-side switch. Qoss and Qgd change with voltage, so use values measured near your operating VDS. The plateau voltage changes with drain current (example 1 uses the datasheet’s 2.4 V at 50 A), and a lower plateau at a lighter load makes turn-off slower. θJA on a datasheet is for a specific copper area (6 cm² for the BSC010N04LSC figure) and a smaller pad is worse, so measure the case temperature on the bench and work back to Tj.

Glossary

RDS(on)
Drain-source resistance of the fully enhanced MOSFET at a stated VGS, ID and temperature.
Qgd (Miller charge)
Gate charge delivered on the plateau while the drain voltage swings; it sets the voltage transition time.
Qgs2
Gate charge from the threshold to the plateau, during which the drain current rises or falls; Qgs − Qg(th).
Plateau voltage
The flat VGS level on the gate charge curve while the drain voltage transitions.
Qoss
Charge stored in the output capacitance at a stated VDS; ½ × Qoss × V is lost at each hard turn-on.
θJA
Thermal resistance from junction to ambient, in °C/W; it depends heavily on the PCB copper.
Hard switching
Turning on or off while the device carries current and blocks voltage, so both overlap during the edge.
Synchronous rectifier
The low-side MOSFET that replaces the catch diode in a synchronous buck converter.

Related guides

Frequently asked questions

How do you calculate MOSFET power dissipation?

Add the conduction loss Irms² × RDS(on) at the junction temperature, the switching loss ½ × V × I × (ton + toff) × fs, and the output capacitance loss ½ × Qoss × V × fs. Then Tj = Ta + θJA × P, and because RDS(on) rises with Tj the two have to be solved together, which this MOSFET power dissipation calculator does. Body-diode conduction and reverse recovery add to this where they apply, and the calculator leaves them out.

What is the MOSFET switching loss formula?

MOSFET switching losses come from the overlap: during each edge the MOSFET carries current and blocks voltage at the same time, so Psw = V/2 × I × fs × (ton + toff). In example 1 (20 V, 20 A, 200 kHz) the gate charge gives ton = 7.8 ns and toff = 26.2 ns, so the switching loss is 1.44 W, most of it at turn-off where the gate current is only Vplateau ÷ Rg.

How much does RDS(on) increase with temperature?

Read it from the datasheet graph of normalized RDS(on) against Tj. The BSC010N04LSC is about 1.5 times its 25 °C value at 125 °C, which corresponds to α = 0.41 %/K in the exponential model RDS(on)(Tj) = RDS(on)(25 °C) × (1 + α/100)^(Tj − 25). Always start from the maximum RDS(on), not the typical.

Is the gate drive loss dissipated in the MOSFET?

Mostly not. Qg × Vdrive × fs (190 mW in example 1) is dissipated in the resistances of the gate loop: the driver output, the external gate resistor and the MOSFET’s internal gate resistance, in proportion to their values. It matters for the driver and the bias supply.

Can I use the rise and fall times from the datasheet?

Only as a rough first pass. Datasheet tr and tf are measured with a specific gate resistor, drive voltage and load current, and they describe the drain voltage edge (Vishay AN608A equates them with the voltage fall and rise times), not the whole current and voltage overlap. The gate charge mode of this MOSFET switching loss calculator computes ton and toff from Qgs2, Qgd, the plateau voltage and your gate resistance, so it tracks your actual driver.

Which loss dominates, conduction or switching?

It depends on frequency and voltage. In the motor drive example (24 V, 20 kHz) conduction is 301 mW against 191 mW of switching loss; in example 1 (20 V, 200 kHz, a 1 mΩ part) switching is 1.44 W against 150 mW of conduction. Low RDS(on) parts have more gate charge, so the best part balances the two at your frequency.

What about the low-side MOSFET in a synchronous buck?

It turns on and off while its body diode carries the current, so its switching loss is close to zero (TI SLVAEQ9). Its loss is conduction over 1 − D, plus body-diode conduction during the dead times and its share of the Coss and reverse-recovery losses. Use the synchronous rectifier preset with zero transition times.

What is power dissipation in a MOSFET?

It is the electrical power the MOSFET turns into heat. This calculator adds conduction loss, switching loss and output capacitance loss, and leaves out body-diode conduction and reverse recovery. In example 1 that is 1.75 W. The gate drive power is mostly dissipated outside the MOSFET, in the gate loop.

How hot does a MOSFET get from these losses?

Tj = Ta + θ × (Pcond + Psw + PCoss). RDS(on) rises with Tj, so the calculator solves conduction loss and temperature together. Example 2 settles at 60 °C with 60 °C/W and 40 °C ambient.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.