NewAI Part GeneratorFree to get started
FREE TOOL

RC snubber calculator

Two ring-frequency measurements give this RC snubber calculator the parasitic inductance and capacitance of a switching node, and from those it sets the snubber resistor and capacitor by published design rules. See the resistor power and a simulated step response, with and without the snubber.

Starting from
Examples
Hz
Hz
F

Fitted directly across the ringing device. Use a value several times its output capacitance.

V
Hz

Snubber R and C

2.15 Ω + 2.42 nF

TI Power Tips: R = Z0, Cs = 3 C

Nearest E24 resistor
2.2 Ω
Nearest E12 capacitor
2.2 nF
Resistor power
31.7 mW Cs V² fs, an upper bound
Peak resistor current
5.45 A V / R
Parasitic capacitance C
807 pF
Parasitic inductance L
3.73 nH
Characteristic impedance Z0
2.15 Ω
Ring frequency f0
91.74 MHz
Snubber corner
32.9 MHz 0.36 × f0
Damping ζ with Cs as a short
0.489
Modeled peak with snubber
17.5 V 1.46 × step
Modeled peak, no snubber
24 V lossless
Settles to ±5 %
17.7 ns 1.6 ring periods

The modeled peak uses an ideal step, lossless L and C, and no current in L at the start. A finite edge and losses lower the real peak, while reverse-recovery current already in L raises it. Treat these as starting values and confirm on the scope.

Node voltage after a 12 V step
0510152025010n20n30n40n50n60n70n80n90nTime (s)Node voltage (V)12 V final
With 2.2 Ω + 2.2 nFNo snubber, lossless

Published rules on this node (nearest standard values)

RuleRCsPeak / stepPower
TI Power Tips2.2 Ω2.2 nF1.46 ×31.7 mW
Nexperia AN111602.2 Ω1.5 nF1.54 ×21.6 mW
TI SLPA010, Cs = C1.1 Ω820 pF1.79 ×11.8 mW

How do you pick R and C in an RC snubber design?

Measure the ring frequency f0, add a known capacitor Cadd and measure the lower frequency f1. Then C = Cadd ÷ ((f0 ÷ f1)² − 1), L = 1 ÷ ((2π f0)² C), Rs = √(L/C) and Cs = 3 × C. TI’s flyback rectifier rang at 19.2 MHz and 12.0 MHz with 100 pF added, which gives 64.1 pF and 1.07 µH, so Rs = 129 Ω and Cs = 192 pF. TI fitted 130 Ω and 200 pF. The resistor dissipates Cs V² fs.

Snubber circuit formulas for R, C and resistor power

Ringing comes from the stray inductance and the device capacitance. Adding a known capacitor lowers the frequency, and the amount it moves reveals both unknowns.

m = f0 ÷ f1     C = Cadd ÷ (m² − 1)     L = 1 ÷ ((2π f0)² C)
f0
ring frequency with nothing added
f1
ring frequency with Cadd across the same device
Cadd
known added capacitor
C
parasitic capacitance
L
parasitic inductance

The published starting points differ in resistor and capacitor, in terms of Z0 = √(L/C):

ζ = Z0 ÷ (2 Rs)     fc = 1 ÷ (2π Rs Cs)
TI SSZTBC7
Rs = Z0, Cs = 3 × C
Nexperia AN11160
Cs = 1 to 2 × C (2 × C in its example), then Rs between √(L/Cs) and 2 × √(L/Cs). The example lands on 1.5 × √(L/Cs), which is 1.06 × Z0 at Cs = 2 × C
TI SLPA010
Rs = Z0 ÷ 2, Cs between ½ and 2 × C

The damping factor treats Cs as a short at the ring frequency. TI SLPA010 uses this parallel LCR approximation and puts a damping factor of 1 at Rs = Z0 ÷ 2. It is close only when Cs is much larger than C. AN11160 uses a different form built on Cs, ζ = Rs ÷ (2 × √(L/Cs)), and aims for 0.5 to 1. The snubber resistor dissipates ½ Cs V² on each edge, two edges per switching cycle:

P = Cs × V² × fs
V
voltage swing at the node
fs
switching frequency

Size the resistor for this figure and you have margin. Nexperia AN11160 gives it as the total snubber loss (eq. 3) and puts less in the resistor itself, (fs ÷ 2)(Cs V² + L I²rm) in eq. 26, which is 103 mW against 192 mW in its example.

RC snubber calculation examples

Example 1: Nexperia’s half bridge

AN11160 Rev. 3.1 measures f0 = 91.74 MHz, and f1 = 61.3 MHz with 1 nF added. The ratio is 1.497, so C = 807 pF and L = 3.73 nH (the note gets 807 pF and 3.73 nH). It takes Cs = 2 × C = 1.61 nF, and trials inside its √(L/Cs) to 2 × √(L/Cs) range land on 1.5 × √(L/Cs) = 2.28 Ω. The note builds it with 2.2 Ω and 1.6 nF, and its Figure 6 shows the oscillation gone. On this node, the TI rule would give 2.15 Ω and 2.42 nF. In the ideal-step model that peaks at 1.43 × the step, against 1.53 × for the Nexperia values and 2.00 × with no snubber, for 50 % more resistor power.

Example 2: TI’s flyback rectifier

In SSZTBC7 the rectifier rings at f0 = 19.2 MHz, and at f1 = 12.0 MHz with 100 pF added. m = 1.60, so C = 64.1 pF and L = 1.07 µH. The rule gives Rs = 129 Ω and Cs = 192 pF, with a corner at 6.4 MHz. TI fitted 130 Ω and 200 pF, and the ringing spike on the scope fell from 355 V to 145 V.

Example 3: a 48 V half bridge

L = 5 nH and C = 700 pF (close to the 706 pF typical output capacitance of a CSD19532Q5B) give Z0 = 2.67 Ω. Using standard values near the TI rule, 2.7 Ω and 2.2 nF peak at 1.43 × the step. At 48 V and 250 kHz the resistor dissipates 1.27 W, more than a single small chip resistor can take, so lowering Cs and accepting more ringing is the usual trade.

Peak versus snubber size

Step response peak as a multiple of the step, from the same simulation the calculator uses (ideal step, lossless L and C, no starting current in L). Larger Cs reduces the peak, though not in proportion, and raises the power in direct proportion.

Cs ÷ CR = 0.5 × Z0R = 1 × Z0R = 2 × Z0Power relative to Cs = C
0.51.91 ×1.85 ×1.80 ×0.5 ×
11.80 ×1.70 ×1.68 ×1 ×
21.63 ×1.53 ×1.58 ×2 ×
31.52 ×1.43 ×1.54 ×3 ×
41.45 ×1.38 ×1.52 ×4 ×
61.35 ×1.31 ×1.49 ×6 ×
101.25 ×1.26 ×1.47 ×10 ×

Snubber resistor power at 100 kHz

P = Cs V² fs. Scale linearly with frequency: double the frequency, double the power.

Cs \ V12 V24 V48 V100 V400 V
100 pF1.44 mW5.76 mW23 mW100 mW1.6 W
470 pF6.77 mW27.1 mW108 mW470 mW7.52 W
1 nF14.4 mW57.6 mW230 mW1 W16 W
4.7 nF67.7 mW271 mW1.08 W4.7 W75.2 W
10 nF144 mW576 mW2.3 W10 W160 W

Getting it to work on the board

Treat the output as a starting point. Device capacitance is voltage dependent, so measure the ringing at the operating voltage and load, and take Coss at the off-state voltage if you are using the datasheet. A wide-bandwidth probe with a short ground spring matters: a long ground lead adds its own inductance and can show a ring that is not in the circuit.

The step model starts with no current in L. A ring set off by reverse recovery, as in the Nexperia example above, starts with current already in L and can peak higher than the model shows, so use the modeled peak to compare designs rather than to predict the spike.

The resistor needs low inductance and enough pulse rating, and the capacitor needs to handle the full voltage with a good dv/dt rating. Snubber loss is often a large part of the total at high voltage: if the power is too high, reduce Cs and accept more ringing, or fix the source of the ringing first with a tighter commutation loop or a slower gate drive.

Glossary

RC snubber
A resistor and capacitor in series across a switching device, which damps the ringing after an edge.
Ring frequency
The frequency of the oscillation set by the parasitic L and C, f0 = 1 ÷ (2π√(LC)).
Parasitic capacitance
The capacitance at the ringing node, often mostly Coss of the off device or the reverse capacitance of a rectifier.
Leakage or stray inductance
Unintended inductance in the commutation loop from PCB traces, package leads or transformer leakage.
Characteristic impedance (Z0)
√(L/C), the impedance level of the LC tank and the reference for sizing the damping resistor.
Damping factor (ζ)
How quickly the ringing decays. ζ = 1 is critically damped, and below that the response overshoots.

Related guides

Frequently asked questions

How do you calculate RC snubber values?

Find the parasitic L and C, then use Rs = √(L/C) and Cs = 3 × C as a starting point. TI’s flyback measurement gives 1.07 µH and 64.1 pF, so Rs = 129 Ω and Cs = 192 pF. TI fitted 130 Ω and 200 pF. Expect to trim the values on the bench.

How do I measure the parasitic inductance and capacitance?

Measure the ring frequency f0, fit a known capacitor Cadd across the same device, and measure the lower frequency f1. Then C = Cadd ÷ ((f0 ÷ f1)² − 1) and L = 1 ÷ ((2π f0)² C). This needs only an oscilloscope and one capacitor.

What size capacitor should I add for the measurement?

Several times the device capacitance, as a starting point. TI’s procedure used 100 pF on a rectifier with 22 pF of reverse capacitance and considers a frequency shift of at least 50 % reasonable. A small shift amplifies the measurement error.

How much power does the snubber resistor dissipate?

P = Cs V² fs. Each edge dissipates ½ Cs V² in the resistor, and there are two edges per cycle, so 2.2 nF swinging 48 V at 250 kHz dissipates 1.27 W. TI SLPA010 writes ½ C V² f, which counts one edge per cycle. Nexperia AN11160 gives Cs V² fs as the total snubber loss and puts ½ Cs V² + ½ L IRM² per cycle in the resistor, where IRM is the peak recovery current.

Does the resistor value change the snubber power?

Not when the RC settles between edges. The energy per edge is ½ C V² whatever the resistor is, so R decides how well the ringing damps while C decides the power.

Should the snubber resistor be Z0 or Z0/2?

It depends on Cs. Z0/2 is critical damping only when Cs is large enough to look like a short at the ring frequency, and it is where TI SLPA010 starts. In the ideal-step model, TI’s Z0 with 3 × C peaks at 1.43 × the step and Nexperia’s 1.5 × √(L/Cs) with 2 × C (about 1.06 × Z0) at 1.53 ×. Try the options on the bench.

Where should the snubber go on the board?

Directly across the device that rings, with the shortest possible loop. Any inductance in series with the RC branch reduces how well it damps a fast ring.

How does the snubber capacitor calculation work?

Start from the parasitic capacitance C at the ringing node. TI SSZTBC7 uses Cs = 3 × C, Nexperia AN11160 uses 1 to 2 × C, and TI SLPA010 uses ½ to 2 × C. A larger Cs reduces the peak, though not in proportion, while the resistor power rises in direct proportion to Cs.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.