NewAI Part GeneratorFree to get started
FREE TOOL

Bootstrap capacitor calculator

From the MOSFET gate charge, the driver’s quiescent current, the switching frequency and the droop you allow, this bootstrap capacitor calculator finds the minimum value for a high-side gate driver. Check a chosen capacitor against UVLO and see the diode, resistor and VDD bypass figures that go with it.

Solve for
Examples
C

At your gate-drive voltage, from the FET datasheet.

Hz
%
V
V

At the charging current. Add the low-side drop here if it is significant.

V

HB-HS or VBS falling threshold from the driver datasheet.

A

IHB or IQBS in the driver datasheet.

A

Optional: flows only while the switch node is high.

V

Blank uses 10 % of VDD − Vf, TI’s rule of thumb.

×

For DC bias, tolerance and skipped cycles. Sets the suggested value only.

C

Optional. IR quotes 5 nC for 500/600 V ICs and 20 nC for 1200 V ICs.

A

Optional: only matters for an electrolytic.

Ω

Optional: gives peak current and charge time.

V

Optional: sets the diode reverse rating.

Minimum Cboot

64.3 nF

500 mV droop, before margin

Charge per cycle Qtotal
32.15 nC
Droop budget to UVLO
2.7 V
Absolute minimum, droop to UVLO
11.9 nF
10 × Cg rule
28.6 nF
Suggested capacitor
150 nF next E6 value above ×2 margin
Droop with 150 nF
214 mV
Longest on-time with 150 nF
5.75 ms until UVLO
Diode average current
3.21 mA Q × f
Diode reverse rating, at least
400 V plus your margin
VDD bypass capacitor, at least
1.5 µF 10 × Cboot
Capacitor voltage rating
24 V 2 × VDD (TI guidance)
Peak charge current
5 A
First-charge energy in Rboot
9.07 µJ
Charge time, about 3 RC
990 ns

Use a low-ESR ceramic capacitor and read its capacitance at the bias voltage from the DC-bias curve. Enter driver and FET values from the maximum column for a worst-case result.

Minimum capacitor versus switching frequency
20n50n100n1k10k100k1M10MSwitching frequency (Hz)Minimum Cboot (F)fsw 100 kHz
Droop 500 mVDroop to UVLO (2.7 V)

Minimum capacitor by method

MethodMinimum Cboot
TI SLUA887A, droop to UVLO (2.7 V)11.9 nF
TI SLUA887A, 10 × Cg28.6 nF
IR DT98-2, absolute minimum11.6 nF
IR DT98-2, × 15 rule of thumb174 nF

How does bootstrap capacitor sizing work?

Use Cboot ≥ Qtotal ÷ ΔV, where Qtotal = Qg + IHBS × Dmax ÷ fsw + IHB ÷ fsw. TI’s UCC27710 example has Qg = 31.5 nC and IHB = 65 µA at 100 kHz, so Qtotal = 32.15 nC. For 0.5 V of droop the minimum is 64.3 nF, and the datasheet fits 220 nF to allow for DC bias, temperature and skipped cycles.

Bootstrap capacitor formula

Each cycle the capacitor gives up the gate charge plus whatever the high-side driver draws while it is floating. The size follows from that charge and the voltage it may lose.

Qtotal = Qg + Qextra + IHBS × Dmax ÷ fsw + (IHB + Icap) ÷ fsw
Qg
MOSFET total gate charge at the drive voltage
Qextra
level-shift charge and diode reverse recovery charge, if not already in IHB
IHBS
HB-to-VSS leakage, which flows only while the switch node is high
Dmax
maximum high-side duty cycle
IHB
high-side quiescent current
Icap
capacitor leakage, relevant only for an electrolytic
fsw
switching frequency

The capacitor then follows from the droop you allow, which can be no more than the margin to UVLO:

Cboot ≥ Qtotal ÷ ΔV     ΔV ≤ VDD − Vf − VUVLO
ΔV
allowed droop
VDD
gate driver supply
Vf
bootstrap diode forward drop
VUVLO
high-side undervoltage lockout, falling threshold

TI’s rule of thumb is a capacitor at least ten times the equivalent gate capacitance, which keeps the droop from the gate charge under about 10 %:

Cboot ≥ 10 × Qg ÷ (VDD − Vf)

The International Rectifier version doubles the gate charge and then the total, with VLS the low-side drop. Its note calls this the absolute minimum and multiplies by 15 as a rule of thumb:

C ≥ 2 × [2Qg + Iqbs ÷ f + Qls + Icbs ÷ f] ÷ (Vcc − Vf − VLS)

The longest on-time before UVLO, the average diode current and the peak charging current are:

tON,max = (Cboot × (VDD − Vf − VUVLO) − Qg − Qextra) ÷ (IHB + IHBS + Icap)
IF(avg) = Qtotal × fsw     IF(peak) = (VDD − Vf) ÷ Rboot

Bootstrap capacitor calculation examples

Example 1: the UCC27710 datasheet design

Qg = 31.5 nC, IQBS = 65 µA (typical), fsw = 100 kHz. Qtotal = 31.5 nC + 65 µA ÷ 100 kHz = 32.15 nC. For 0.5 V of droop, Cboot ≥ 64.3 nF. The datasheet fits 220 nF, which droops 146 mV per cycle, and a VDD bypass of 10 × Cboot = 2.2 µF. A 2.2 Ω bootstrap resistor limits the peak diode current to 5 A with VDD − Vf = 11 V, and absorbs 13.3 µJ on the first charge.

Example 2: IR2110 bootstrap capacitor calculation with an IRF540 at 20 kHz, maximum values

Qg = 72 nC (IRF540 maximum), IQBS = 230 µA (IR2110 maximum), Qls = 5 nC, 15 V supply, 1 V diode drop. At 20 kHz the quiescent current takes 230 µA ÷ 20 kHz = 11.5 nC, so Qtotal = 88.5 nC. For 0.5 V of droop, Cboot ≥ 177 nF. With VBSUV− = 9.4 V (maximum) the budget to UVLO is 4.6 V, and a 470 nF capacitor holds up for 9.07 ms, well beyond the 47.5 µs on-time at 95 % duty. The IR note’s minimum on the same data is 22.9 nF.

Example 3: UCC27211 and CSD19532Q5B at 300 kHz, typical values

Qg = 48 nC (at 10 V), IHB = 65 µA, IHBS = 1 µA (maximum), 12 V supply, 0.9 V diode drop. Qtotal = 48.22 nC, almost all gate charge at this frequency, and 0.5 V of droop needs 96.4 nF. The 10 × Cg rule gives 43.2 nF and the budget to the 5.6 V typical UVLO is 5.5 V. The diode carries an average of 14.5 mA.

Bootstrap capacitor selection table: minimum Cboot by gate charge and droop

Qtotal ÷ ΔV at 100 kHz, 50 % duty and 100 µA of quiescent current. These are minimums: add margin for DC bias, tolerance and skipped cycles.

Qg \ droop250 mV500 mV1 V
10 nC44 nF22 nF11 nF
30 nC124 nF62 nF31 nF
50 nC204 nF102 nF51 nF
100 nC404 nF202 nF101 nF
200 nC804 nF402 nF201 nF

How frequency changes the requirement

Qg = 50 nC, 200 µA of quiescent current, 0.5 V of droop. At low frequency the capacitor spends more time supplying the driver, so the quiescent term grows.

fswQtotalMinimum CbootShare from quiescent current
1 kHz250 nC500 nF80 %
5 kHz90 nC180 nF44 %
20 kHz60 nC120 nF17 %
100 kHz52 nC104 nF4 %
500 kHz50.4 nC101 nF1 %

Where the bootstrap goes wrong

Datasheet quiescent current is only the DC figure. The UCC27211 specifies 65 µA typical for IHB, but its operating current IHBO is 1.3 mA typical at 500 kHz with no load, which is 2.6 nC per cycle rather than 130 pC. If gate charge is small or the frequency is high, use the operating figure.

Ceramic capacitors lose capacitance under DC bias, so the value that counts is the one on the DC-bias curve at your bootstrap voltage. That loss, tolerance and skipped cycles during load transients are the reasons the calculated minimum is not the value to fit. Use the margin field for that, and place the capacitor directly at the HB and HS pins.

The capacitor only recharges when the switch node is low, so the high side needs a minimum off-time. At start-up the low side must conduct first, for several RC periods if the bootstrap resistor is large. When the switch node swings below ground, the capacitor can charge to VDD plus the undershoot. A small resistor in series with the diode reduces that, though TI notes it is not foolproof and it slows the recharge.

Glossary

Bootstrap capacitor (Cboot)
The capacitor from HB to HS that powers the floating high-side driver and supplies the gate charge.
Switch node (HS or VS)
The midpoint of the half bridge, which swings between ground and the bus each cycle.
Total gate charge (Qg)
The charge delivered to the gate to reach the drive voltage, from the MOSFET datasheet.
Droop
The drop in bootstrap voltage over one cycle as the capacitor supplies charge.
UVLO
Undervoltage lockout: the driver turns the output off if the bootstrap voltage falls below this threshold.
Level-shift charge (Qls)
Charge taken each cycle by the level shifter inside a high-voltage driver IC. IR quotes 5 nC for 500/600 V ICs and 20 nC for 1200 V ICs.

Related guides

Frequently asked questions

How do you calculate the bootstrap capacitor value?

Add up the charge taken each cycle, Qtotal = Qg + IHBS × Dmax ÷ fsw + IHB ÷ fsw, and divide by the droop you allow. TI’s UCC27710 example gets 32.15 nC per cycle, which needs 64.3 nF for 0.5 V of droop, and then fits 220 nF for margin.

What bootstrap capacitor do I need for a 100 nC MOSFET?

At 100 kHz with 100 µA of quiescent current and 0.5 V of droop, the minimum is 202 nF. With a ×2 margin for DC bias and tolerance that is 404 nF, so the next E6 value is 470 nF.

Why does a bigger bootstrap capacitor not always work better?

A larger capacitor takes longer to charge and draws more peak current through the diode (TI SLUA887A, equation 4). If the low-side on-time is short, it may never fully recharge. IR’s DT98-2 warns of the opposite problem with values that are too small, which can overcharge and damage the IC.

What bootstrap capacitor voltage rating and type should I use?

TI recommends low-ESR, low-ESL surface-mount ceramic capacitors with a rating of about 2 × VDD. Read the capacitance at the bias voltage from the DC-bias curve, because an X7R or X5R part can lose a large share of its nominal value.

How do I choose the bootstrap diode?

It blocks the full bus voltage when the high side is on, so VRRM must exceed the bus with margin. IR’s DT98-2 asks for a recovery time of 100 ns or less and an average current of Qbs × f. TI recommends a fast-recovery or Schottky diode with low forward drop and low junction capacitance.

Can a bootstrap driver run at 100 % duty?

Only for a limited time. The capacitor recharges only when the switch node is low, and quiescent current drains it meanwhile. With the UCC27710 example values, 1 µF holds the high side on for about 41.1 ms before reaching UVLO. Past that you need a charge pump or an isolated supply.

Why do TI and IR give such different answers?

They are aimed at different margins. TI’s formula is the charge balance alone, and IR’s DT98-2 doubles both gate charge and total charge, then multiplies by 15 as a rule of thumb against overcharging. For the IR2110 example TI’s balance needs 177 nF for 0.5 V of droop, while IR’s method gives 22.9 nF as its absolute minimum and 344 nF with the factor of 15.

What bootstrap capacitor value does an IR2110 need?

With an IRF540 at 20 kHz, a 15 V supply, a 1 V diode drop and maximum datasheet values, Qtotal is 88.5 nC, so 0.5 V of droop needs at least 177 nF. IR’s DT98-2 minimum on the same data is 22.9 nF. A 470 nF capacitor holds the high side up for 9.07 ms before UVLO.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.