NewAI Part GeneratorFree to get started
FREE TOOL

Boost converter calculator

For a new step-up design, this boost converter calculator sizes the inductor and output capacitor. If you already have the parts, it checks the ripple, peak switch current and maximum output current instead. It follows TI's design equations and draws the inductor current waveform.

Solve for
Examples
V
V

Optional: finds the input where the ripple is largest and sizes the inductor for it.

V
A
Hz

Use the minimum from the data sheet.

%

TI uses 80 % to 85 % as a worst-case estimate; 100 % gives the ideal duty cycle.

%

Percent of Iout × Vout ÷ Vin. TI suggests 20 to 40.

V
Ω
A

Optional: from the data sheet. Checks whether the IC can deliver the load.

V

Optional: for a non-synchronous design.

Inductor

8.102 µH

exact value

Duty cycle D
64.58 %
Average inductor current
2.824 A
Next E12 inductor
8.2 µH used below
Ripple current
787.6 mA target 720 mA
Peak inductor and switch current
3.217 A
Valley inductor current
2.43 A
Minimum output capacitance
12.4 µF effective, after derating
ESR ripple
16.1 mV
Output capacitor RMS current
1.35 A
Stays in CCM down to a load of
139 mA
Right-half-plane zero
29.2 kHz full load, minimum input, loss-adjusted D

Continuous-conduction equations from TI SLVA372. Duty cycle, ripple and peak current are at the minimum input voltage, where the switch current is highest.

The ripple uses the loss-adjusted duty cycle (SLVA372 Eq. 2) while Eq. 5 and 6 are lossless, so it can read above the target. Treat it as the conservative value.

Ripple is largest at 50 % duty, near 7.06 V of input. If the input can rise that far, enter the maximum input voltage so the inductor is sized for it.

Keep the control loop crossover below 9.74 kHz (one third of the right-half-plane zero) and below one fifth of the switching frequency.

Ceramic capacitors lose capacitance under DC bias. Use the effective value, not the printed one.

Inductor current over two switching periods
01230500n1µ1.5µ2µ2.5µ3µ3.5µ4µTime (s)Inductor current (A)Average 2.82 APeak 3.22 AValley 2.43 ASwitch off, 1.29 µs

Other ripple targets

Ripple targetInductorNext E12RipplePeak current
20 %12.2 µH15 µH431 mA3.04 A
30 %8.1 µH8.2 µH788 mA3.22 A
40 %6.08 µH6.8 µH950 mA3.3 A

How do you calculate the duty cycle and inductor in a boost converter design?

Use D = 1 − (Vin × η) ÷ Vout and L = Vin × (Vout − Vin) ÷ (ΔIL × fs × Vout), with the ripple ΔIL at 20 % to 40 % of Iout × Vout ÷ Vin. For 5 V to 12 V at 1 A, 500 kHz and 85 % efficiency, D = 64.6 %. A 30 % ripple target (720 mA) needs 8.1 µH, so use 8.2 µH, which gives a peak switch current of 3.22 A.

Boost converter formulas

These boost converter design equations are the continuous-conduction set from TI application note SLVA372D, with its equation numbers. Duty cycle, ripple and peak current are evaluated at the minimum input voltage, which gives the highest switch current.

D = 1 − (Vin × η) ÷ Vout     (Eq. 1)
ΔIL = Vin × D ÷ (fs × L)     (Eq. 2)
D
duty cycle
Vin
minimum input voltage in V
Vout
output voltage in V
η
efficiency as a fraction; TI uses 80 % to 85 % as a worst-case estimate
fs
minimum switching frequency in Hz
L
inductance in H
ΔIL
peak-to-peak inductor ripple current in A

Sizing the inductor for a chosen ripple, normally 20 % to 40 % of the inductor current:

L = Vin × (Vout − Vin) ÷ (ΔIL × fs × Vout)     (Eq. 5)
ΔIL = (0.2 to 0.4) × Iout × Vout ÷ Vin     (Eq. 6)

SLVA372D writes Eq. 5 and 6 with the typical input voltage. This calculator uses the minimum for Eq. 6 and, when you enter a maximum, evaluates Eq. 5 at the input closest to Vout ÷ 2, where the lossless duty cycle is 50 % and the ripple is largest (SLVA061, and the method in the TPS55340 data sheet). Peak current and the most an IC can deliver:

Ipeak = ΔIL ÷ 2 + Iout ÷ (1 − D)     (Eq. 4)
Imaxout = (Ilim(min) − ΔIL ÷ 2) × (1 − D)     (Eq. 3)

The output capacitor and its ESR ripple:

Cout = Iout × D ÷ (fs × ΔV)     (Eq. 12)
ΔV(ESR) = ESR × (Iout ÷ (1 − D) + ΔIL ÷ 2)     (Eq. 13)

When an ESR is entered, the capacitor is sized for whatever ripple budget the ESR leaves. The rectifier carries the output current (Eq. 7 and 8), and SLVA061 gives the capacitor RMS current, the boundary of continuous conduction and the right-half-plane zero, shown here neglecting inductor resistance. The zero uses the loss-adjusted D from Eq. 1, so below 100 % efficiency it reads lower than the (Vin ÷ Vout)² form in the TPS55340 data sheet, which is the safe direction for setting the loop crossover:

PD = Iout × VF     I(Cout, RMS) = Iout × √(D ÷ (1 − D))
Iout(crit) = ΔIL × (1 − D) ÷ 2     fRHP = (1 − D)² × (Vout ÷ Iout) ÷ (2π × L)

Boost converter design examples

Example 1: 5 V to 12 V at 1 A

At 500 kHz with an estimated 85 % efficiency, D = 1 − (5 × 0.85) ÷ 12 = 64.6 %, so the inductor carries 2.82 A on average. A 30 % ripple target is 0.3 × 1 × 12 ÷ 5 = 720 mA, and Eq. 5 gives 8.1 µH. The next E12 value is 8.2 µH. Eq. 2 then gives 788 mA of ripple and a peak of 3.22 A.

With 5 mΩ of ESR (16.1 mV of ripple) and a 120 mV limit, the output needs at least 12.4 µF of effective capacitance, rated for 1.35 A RMS. The right-half-plane zero at full load is 29.2 kHz, so keep the loop crossover below 9.74 kHz.

Example 2: reproducing TI's TPS55340 design

TI's data sheet example boosts 5 V to 12 V up to 24 V at 0.8 A and 600 kHz with 10 µH and an 85 % efficiency estimate. It computes the ripple from a duty cycle that includes the 0.5 V diode drop, 1 − 5 ÷ 24.5 = 79.6 %. With that D, Eq. 2 gives 663 mA of ripple (published: 663 mA), the average input current is 4.52 A (published: 4.52 A), and the peak is 4.85 A (published: 4.85 A). Eq. 12 gives 8.84 µF for a 120 mV ripple (published: 8.8 µF), the capacitor RMS current is 1.58 A (published: 1.58 A), and a 5.25 A switch limit allows 871 mA (published: 871 mA).

SLVA372D's duty cycle with η instead gives 82.3 %, 686 mA of ripple, a 4.86 A peak and 869 mA maximum output. That is what the calculator shows for these parts, and the small gap is the difference between the two ways of estimating D.

Example 3: how much can a 3 A switch deliver?

Boosting 3.3 V to 5 V at 1 MHz with 4.7 µH and 85 % efficiency, D = 43.9 % and the ripple is 308 mA. A 3 A minimum switch limit allows (3 − 154 mA) × (1 − D) = 1.6 A of output current, about half of the switch limit. At a 1 A load, a 0.4 V Schottky rectifier dissipates 400 mW.

Boost converter inductor selection for common conversions

Computed for 1 A output, 500 kHz, 85 % efficiency and a 30 % ripple target. Peak current uses the next E12 inductor. For any other conversion, use the boost inductor calculator above.

ConversionDuty cycleAverage ILInductorNext E12Peak currentCCM down to
3.3 V to 5 V43.9 %1.78 A4.94 µH5.6 µH2.04 A145 mA
3.3 V to 12 V76.6 %4.28 A4.39 µH4.7 µH4.82 A126 mA
5 V to 9 V52.8 %2.12 A8.23 µH10 µH2.38 A125 mA
5 V to 12 V64.6 %2.82 A8.1 µH8.2 µH3.22 A139 mA
5 V to 24 V82.3 %5.65 A5.5 µH5.6 µH6.38 A130 mA
12 V to 24 V57.5 %2.35 A20 µH22 µH2.67 A133 mA
12 V to 36 V71.7 %3.53 A17.8 µH18 µH4.01 A135 mA
12 V to 48 V78.8 %4.71 A15 µH15 µH5.34 A134 mA
24 V to 48 V57.5 %2.35 A40 µH47 µH2.65 A125 mA

Maximum output current versus input voltage

A boost regulator's output current depends on how much it has to boost. These figures are for a 12 V output from an IC with a 3 A minimum switch limit, 10 µH, 500 kHz and 85 % efficiency.

Input voltageDuty cycleRippleMaximum output current
3.3 V76.6 %506 mA642 mA
5 V64.6 %646 mA948 mA
6 V57.5 %690 mA1.13 A
8 V43.3 %693 mA1.5 A
9 V36.3 %653 mA1.7 A
10 V29.2 %583 mA1.92 A

What goes wrong in real converters

The data sheet comes first. If it recommends an inductor or range, use it; an internally compensated regulator needs the recommended values or its documented adjustment for the L × C product. The output capacitor equations here only apply freely with external compensation, where the loop is adjusted to match.

A boost converter has no inherent current limit from input to output: the inductor and diode conduct whenever the input is above the output, including at power-up before switching starts. Check the switch limit against the peak at the minimum input, since that is where the current is highest, and leave margin on the inductor saturation rating. The TPS55340 data sheet recommends rating the inductor about 20 % above the calculated peak.

Ceramic output capacitors lose capacitance under DC bias, and boost outputs tend to run at high voltage. The TPS55340 data sheet notes they can lose as much as 50 % at rated voltage, so use the effective value at the output voltage. This model is steady-state and continuous-conduction only: it does not cover loop stability, start-up, switching loss or light-load behavior.

Glossary

Duty cycle (D)
The fraction of each switching period that the low-side switch is on.
Ripple current (ΔIL)
The peak-to-peak swing of the inductor current in steady state.
Continuous conduction mode (CCM)
Operation in which the inductor current never reaches zero during the switching cycle.
Discontinuous conduction mode (DCM)
Operation in which the inductor current falls to zero and stays there for part of each cycle.
Right-half-plane zero
A zero in the control-to-output response of a boost converter that adds phase lag and limits the loop bandwidth.
ESR
Equivalent series resistance of a capacitor. In a boost it carries the full peak current when the switch turns off.
Boost converter
A DC/DC converter whose output is above its input, also called a step-up converter.

Related guides

Frequently asked questions

What is the boost converter duty cycle formula?

D = 1 − (Vin × η) ÷ Vout. The ideal value is 1 − Vin ÷ Vout; the efficiency term accounts for the extra on-time that supplies the losses. For 5 V to 12 V at 85 % efficiency, D = 64.6 %.

How do I choose the inductor for a boost converter?

If the data sheet recommends a value or range, use it. Otherwise set the ripple to 20 % to 40 % of the inductor current, Iout × Vout ÷ Vin, and compute L = Vin × (Vout − Vin) ÷ (ΔIL × fs × Vout). For 5 V to 12 V at 1 A and 500 kHz, a 30 % target gives 8.1 µH, so buy 8.2 µH.

How do you calculate the boost converter switch current?

Ipeak = ΔIL ÷ 2 + Iout ÷ (1 − D). The switch and inductor carry the input current, which is much larger than the output current at high duty cycles. In the 5 V to 12 V example at 1 A out, the peak is 3.22 A.

Why can a 3 A boost regulator not deliver 3 A?

Its current limit applies to the switch, and the switch carries the input current. The output current available is (Ilim − ΔIL ÷ 2) × (1 − D). A 3 A switch boosting 3.3 V to 5 V at 44 % duty delivers about 1.6 A.

How do I size the output capacitor of a boost converter?

C = Iout × D ÷ (fs × ΔV), because the output capacitor alone feeds the load during the on-time. ESR adds ESR × (Iout ÷ (1 − D) + ΔIL ÷ 2), and it sees the full peak current, so low-ESR ceramics make a large difference. Check the RMS rating too: Iout × √(D ÷ (1 − D)).

What is the right-half-plane zero in a boost converter?

A zero at (1 − D)² × R ÷ (2π × L), with R = Vout ÷ Iout. It adds gain with phase lag, which limits how fast the control loop can be. TI recommends keeping the crossover below one third of it and below one fifth of the switching frequency. In the 5 V to 12 V example it is 29.2 kHz.

When does a boost converter enter discontinuous conduction mode?

When the output current falls below ΔIL × (1 − D) ÷ 2, the inductor current reaches zero before the next cycle. Below that load the duty cycle depends on the load and these equations no longer apply.

Can a boost converter run with the input above the output?

No. Current flows straight through the inductor and diode, so the output follows the input and the converter cannot regulate. If the input can cross the output, use a SEPIC or a buck-boost.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.