NewAI Part GeneratorFree to get started
FREE TOOL

Rectifier filter capacitor calculator

The filter capacitor calculator below sizes the smoothing capacitor after a half-wave, center-tap or bridge rectifier from the load current and the ripple you can accept. See the output waveform, the peak diode current and the RMS ripple current the capacitor has to survive.

Solve for
Examples
Rectifier
Mains frequency
V

For a center-tap winding, each half.

A
V
V

1N400x: up to 1.1 V at 1 A. A bridge has two in the path.

Ω

Secondary winding, plus primary × (Ns/Np)², plus diode resistance. Blank = ideal source.

Minimum capacitance

4.167 mF

I ÷ (k f ΔV)

Next E6 value up
4.7 mF
Ripple with 4.7 mF
1.214 V circuit solution
Peak output
13.84 V
Minimum output
12.63 V
Average output
13.25 V
Capacitor RMS ripple current
1.61 A 1.61 × load
Peak diode current
4.507 A
Diode average current
500 mA
Diode RMS current
1.34 A
Diode conduction per pulse
2.795 ms 60° of the mains cycle
Secondary RMS current
1.896 A
Secondary VA
22.7 VA
Diode reverse voltage
16.97 V minimum, no transients
Peak at 10 % high line
17.27 V capacitor rating must exceed it

Constant-current load, as a linear regulator presents. The formula assumes discharge for the whole rectified period; the circuit solution stops at the next charging pulse, so it reads lower.

Hammond’s rectifier guide warns ripple current can reach 2 to 3 times the DC load. Check it against the capacitor’s rating, at your temperature and frequency.

Waveforms in steady state
0510152001234505m10m15m20m25mTime (s)Voltage (V)Diode current (A)
Capacitor voltageRectified AC after diodesDiode current

Standard E6 values

CapacitorFormula rippleSolved rippleMinimum outputPeak diodeRipple current
1.5 mF5.56 V3.7 V10.8 V4.32 A1.55 A
2.2 mF3.79 V2.56 V11.7 V4.43 A1.59 A
3.3 mF2.53 V1.72 V12.3 V4.48 A1.6 A
4.7 mF1.77 V1.21 V12.6 V4.51 A1.61 A
6.8 mF1.23 V840 mV12.9 V4.52 A1.61 A
10 mF833 mV572 mV13 V4.52 A1.62 A
15 mF556 mV381 mV13.1 V4.53 A1.62 A

How do you calculate the filter capacitor value for a rectifier?

Use C = I ÷ (k × f × ΔV), with k = 2 for a full-wave rectifier and 1 for half-wave. For 1 A and 2 V of ripple from a 60 Hz bridge, C = 1 ÷ (2 × 60 × 2) = 4.17 mF, so use 4.7 mF. Then check the ripple current, which here is 1.61 A RMS, against the capacitor’s rating.

Filter capacitor and ripple voltage formulas

Between charging pulses the capacitor alone feeds the load, so its voltage falls by the charge removed divided by C.

C = I ÷ (k × f × ΔV)     ΔV = I ÷ (k × f × C)
C
capacitance in F
I
DC load current in A
k
1 for half-wave, 2 for full-wave (bridge or center-tap)
f
mains frequency in Hz
ΔV
peak-to-peak ripple in V

The output sits below the transformer peak by the diode drops, and swings by the ripple:

Vpeak = √2 × Vrms − n × Vf     Vdc ≈ Vpeak − ΔV ÷ 2
n
diodes in the current path: 2 for a bridge, 1 otherwise
Vf
forward drop of one diode in V

For small ripple and an ideal source, Sedra and Smith give the conduction angle and peak diode current as below. A real supply is gentler, because the source resistance spreads each pulse. The calculator solves the circuit with your RS to get the currents.

ωΔt ≈ √(2ΔV ÷ Vp)
half-wave: iD,max ≈ I (1 + 2π√(2Vp ÷ ΔV))     full-wave: iD,max ≈ I (1 + 2π√(Vp ÷ (2ΔV)))

The solver integrates the sine source through the diode drops and RS into C at a constant load current, until each rectified period repeats. Checked against O. H. Schade’s 1943 curves as reproduced in National’s handbook, it agrees within about 10 % on RMS diode current and 12 % on peak current, which is about as closely as those curves can be read.

Filter capacitor calculation examples

Example 1: bridge rectifier filter capacitor calculation, 12 V transformer, 1 A, 60 Hz, 2 V ripple

C = 1 ÷ (2 × 60 × 2) = 4.17 mF, so use 4.7 mF. The bridge drops 1.4 V, leaving a peak of 13.8 V with 0.5 Ω in series. The circuit solution gives 1.21 V of ripple and a 12.6 V minimum. The diodes conduct for 2.8 ms per pulse (60° of the mains cycle), with a peak of 4.51 A. The capacitor carries 1.61 A RMS and the winding 1.9 A RMS.

Example 2: 24 V transformer, 3 A, 50 Hz bridge, 3 V ripple

C = 3 ÷ (2 × 50 × 3) = 10 mF, so use 10 mF. With 0.9 V per diode and 0.4 Ω of source resistance, the output runs between 25.9 V and 27.9 V. Ripple current is 4.64 A RMS, peak diode current 12.7 A, and each diode needs at least 33.9 V of reverse rating before any margin.

Example 3: Sedra and Smith’s half-wave peak rectifier

With Vp = 100 V, R = 10 kΩ (10 mA), f = 60 Hz and 5 V of ripple, the textbook approximation gives C = 33.3 µF, ωΔt = 0.316 rad, an average diode current of 209 mA during conduction and a peak of 407 mA. Solving the same circuit exactly gives a peak of 393 mA and a ripple of 4.75 V, because the capacitor stops discharging as soon as the next pulse begins.

Minimum capacitance for common loads

C = I ÷ (k f ΔV) for a full-wave rectifier at 60 Hz. For 50 Hz multiply by 1.2, and for half-wave by 2.

Load \ Ripple0.5 V1 V2 V5 V
100 mA1.67 mF833 µF417 µF167 µF
500 mA8.33 mF4.17 mF2.08 mF833 µF
1 A16.7 mF8.33 mF4.17 mF1.67 mF
2 A33.3 mF16.7 mF8.33 mF3.33 mF
5 A83.3 mF41.7 mF20.8 mF8.33 mF

Rectifier comparison

For a capacitor-input filter, from Hammond’s Design Guide for Rectifier Use. Voltages are in terms of the secondary RMS voltage VAC; for center-tap, VAC is the whole winding.

RectifierkDiodes in pathReverse rating overDC per amp of AC rating
Half-wave112.8 × VAC0.28 A
Center-tap, full-wave211.4 × VAC (whole winding)1.00 A
Bridge, full-wave221.4 × VAC0.62 A

Effect of source resistance on current

The 12 V, 1 A bridge from Example 1 with 4.7 mF. Winding resistance is what keeps the charging pulse in check.

Series RPeak outputRipplePeak diodeRipple current
0 (ideal)15.6 V1.52 V13.4 A2.84 A
0.1 Ω15.3 V1.42 V7.49 A2.22 A
0.25 Ω14.7 V1.32 V5.65 A1.87 A
0.5 Ω13.8 V1.21 V4.51 A1.61 A
1 Ω12.5 V1.08 V3.58 A1.36 A
2 Ω10.3 V916 mV2.83 A1.12 A
5 Ω5.56 V646 mV2.07 A797 mA

What to watch in a real supply

  • Transformers are rated at full load. The secondary rises with no load, and the mains has its own tolerance, so size the capacitor voltage for the no-load peak at high line.
  • Ripple current heats the capacitor, and heat sets its life. Hammond notes that life improves greatly with less RMS current or a cooler ambient.
  • Capacitor tolerance and aging eat into the formula. Electrolytics are commonly ±20 % and lose capacitance over their life, so leave margin on the ripple.
  • The first charge is a surge that is limited only by the source resistance and the ESR. Check the diode surge rating, and use a thermistor or soft start on mains-fed supplies.
  • The constant-current load is accurate for a regulator input. A resistive load draws less as the voltage droops, so its ripple is slightly smaller.
  • Mains-fed rectifiers and their capacitors hold lethal charge after switch-off. Add a bleeder and keep to the creepage and fusing your safety standard requires.

Glossary

Reservoir (filter) capacitor
The capacitor after a rectifier that supplies the load between charging pulses.
Ripple voltage
The peak-to-peak variation of the DC output as the capacitor charges and discharges.
Conduction angle
The part of the mains cycle in which a diode conducts, in degrees.
Ripple current
The RMS AC current through the capacitor; it heats the capacitor through its ESR.
Peak inverse voltage (PIV)
The highest reverse voltage a diode sees.
Source resistance (RS)
Winding resistance referred to the secondary plus diode dynamic resistance, which limits the charging current.

Related guides

Frequently asked questions

What is the filter capacitor formula for a rectifier?

C = I ÷ (k × f × ΔV), with I the load current, f the mains frequency, ΔV the allowed peak-to-peak ripple and k = 1 for half-wave or 2 for full-wave. It assumes the capacitor carries the whole load for a full rectified period, so it errs on the safe side.

What size capacitor for 1 A and 2 V of ripple at 60 Hz?

A full-wave circuit needs 4.17 mF, and the next E6 value up is 4.7 mF. A half-wave circuit needs twice as much, 8.33 mF.

Why does a full-wave rectifier need half the capacitance?

The capacitor gets a charging pulse twice per mains cycle instead of once, so it discharges for half as long at the same load.

How much ripple current does a filter capacitor see?

Much more than the DC load. In the 12 V, 1 A example with 0.5 Ω of source resistance it is 1.61 A RMS. Hammond’s rectifier guide warns it can be 2 to 3 times the DC load. Choose a capacitor rated for it at your temperature.

What voltage rating does the capacitor need?

Above the peak with no load at the highest line voltage. A 12 V secondary peaks at 17 V, but a transformer rated 12 V at full load rises when unloaded, and the mains tolerance adds more, so a 25 V capacitor is a common choice there. Rate for the no-load figure from the transformer datasheet.

Is a bigger filter capacitor always better?

Up to a point. Ripple falls, but the diode conducts for less time, so peak current and turn-on surge rise. With an ideal source the peak in the 12 V, 1 A example would be 13.4 A; the winding resistance is what holds it to 4.51 A.

What reverse voltage and current should the diodes have?

Each bridge diode sees the AC peak, while center-tap and half-wave diodes see twice it. Hammond’s rectifier guide also recommends a current rating of at least twice the output to cover the turn-on surge, and National’s handbook notes that line transients can demand much more reverse voltage.

What is the difference between a bridge and a center-tap rectifier?

Both are full-wave and use the same capacitor. A bridge has two diodes in the path and needs only a single winding, while a center-tap has one diode drop but needs two windings and twice the diode reverse voltage.

What is the full-wave rectifier ripple voltage formula?

ΔV = I ÷ (2 × f × C), with I the load current, f the mains frequency and C the filter capacitance. 1 A at 60 Hz with 4.17 mF gives 2 V peak to peak. For a capacitor you already have, the Ripple tab is a ripple voltage calculator.

What is the half-wave rectifier ripple voltage formula?

ΔV = I ÷ (f × C). The capacitor recharges only once per mains cycle, so the same 1 A and 2 V at 60 Hz take 8.33 mF, twice the full-wave value.

Is a smoothing capacitor the same as a filter capacitor?

Yes. Filter capacitor, smoothing capacitor and reservoir capacitor all name the part after a rectifier that supplies the load between charging pulses.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.