NewAI Part GeneratorFree to get started
FREE TOOL

Heatsink calculator

From the power, θJC and mounting interface, this heatsink calculator finds the highest thermal resistance that keeps a part below its junction limit. You can also check the junction temperature with a heatsink you already have, or the most power it can handle.

Solve for
Examples
W
°C

The datasheet Tj max, less the margin you want to keep.

°C

The air around the heatsink, inside the enclosure if there is one.

°C/W

From the datasheet, to the surface that touches the heatsink (the metal tab).

°C/W

Optional: checks whether you need a heatsink at all.

Maximum heatsink θSA

5.33 °C/W

or lower

Total θJA allowed
7.33 °C/W
Case temperature
127.5 °C
Heatsink temperature
120 °C
Heatsink rise above ambient
80 °C

Heatsink θSA changes with temperature rise and airflow. Read it from the maker’s curve at your power, not from one headline number, and keep your own margin below the datasheet Tj max.

θCS = 0.5 °C/W (Nexperia AN11172, Table 1; IRFZ44N data sheet (0.50 typ)), assuming a flat, clean surface and correct mounting.

Heatsink needed against power
05101520101520253035Power (W)Required θSA (°C/W)15 W: 5.33 °C/W

Temperature at each point, at 15 W

PointTemperatureDrop to next pointθ to next point
Junction150 °C22.5 °C1.5 °C/W
Case127.5 °C7.5 °C0.5 °C/W
Heatsink120 °C80 °C5.33 °C/W
Ambient40 °C

How do you calculate the heatsink thermal resistance you need?

Use θSA = (Tj − Ta) ÷ P − θJC − θCS. For a TO-220 MOSFET with θJC = 1.5 °C/W on grease at 0.5 °C/W, dissipating 15 W in 40 °C air with a 150 °C junction limit, θSA = (150 − 40) ÷ 15 − 1.5 − 0.5 = 5.33 °C/W. Choose a heatsink at or below that value at your power and airflow. A zero or negative answer means no heatsink can meet the limit.

Heatsink thermal resistance formula

Heat flows from the junction to the case, through the interface into the heatsink, and out to the air. The thermal resistances add in series.

Tj = Ta + P × (θJC + θCS + θSA)
Tj
junction temperature limit in °C
Ta
ambient air temperature in °C
P
power dissipated in W
θJC
junction to case, from the datasheet, in °C/W
θCS
case to heatsink (the interface) in °C/W
θSA
heatsink to ambient in °C/W

Solved for the heatsink you need, and for the power a heatsink you have can handle:

θSA = (Tj − Ta) ÷ P − θJC − θCS     Pmax = (Tj − Ta) ÷ (θJC + θCS + θSA)

How to calculate heatsink size: worked examples

Example 1: a TO-220 MOSFET at 15 W

An IRFZ44N has θJC = 1.5 °C/W (max). With compound on a screw mount (θCS = 0.5 °C/W), 40 °C air and a 150 °C limit (margin below its 175 °C rating), θSA = 7.33 − 1.5 − 0.5 = 5.33 °C/W. The case then sits at 127.5 °C and the heatsink at 120 °C. With a 0.05 mm mica insulator (1.4 °C/W) the heatsink has to reach 4.43 °C/W.

Example 2: an LM7805 dropping 7 V at 1 A

P = 7 × 1 = 7 W. With the data sheet’s θJC of 4 °C/W for the TO-220, grease and a 125 °C junction limit at 40 °C: θSA = 12.1 − 4 − 0.5 = 7.64 °C/W.

Example 3: what an existing heatsink can handle

An IRFP250N in TO-247 (θJC = 0.7 °C/W, greased θCS = 0.24 °C/W) on a 5 °C/W heatsink in 40 °C air, with a 175 °C limit: Pmax = (175 − 40) ÷ (0.7 + 0.24 + 5) = 22.7 W, which puts the junction at 175 °C. Even a perfect heatsink would stop at 144 W.

Heatsink sizing table: required θSA by power and ambient

For a part with θJC = 1.5 °C/W on greased TO-220 mounting (0.5 °C/W) and a 150 °C junction limit. Values are in °C/W.

Power \ Ambient25 °C40 °C55 °C70 °C
2 W60.55345.538
5 W23201714
10 W10.597.56
15 W6.335.334.333.33
20 W4.253.52.752
30 W2.171.671.170.667
50 W0.50.2not possiblenot possible

Case-to-sink interface values

Published figures for flat, clean surfaces with the right amount of compound. Rough or warped mounting will be worse.

MountingθCSSource
TO-220, compound, screw0.5 °C/WNexperia AN11172, Table 1; IRFZ44N data sheet (0.50 typ)
TO-220, compound, clip0.3 °C/WNexperia AN11172, Table 1
TO-220, dry, no compound1.4 °C/WNexperia AN11172, Table 1
TO-220, 0.25 mm alumina, compound, clip0.8 °C/WNexperia AN11172, Table 1
TO-220, 0.05 mm mica, compound, screw, to 500 V1.4 °C/WNexperia AN11172, Table 1
TO-220, 0.05 mm mica, compound, screw, to 800/1000 V1.6 °C/WNexperia AN11172, Table 1
TO-220, 0.1 mm mica, compound, clip2.2 °C/WNexperia AN11172, Table 1
TO-220, 0.05 mm mica, no compound, screw, to 500 V3 °C/WNexperia AN11172, Table 1
TO-220, 0.05 mm mica, no compound, screw, to 800/1000 V4.5 °C/WNexperia AN11172, Table 1
TO-220, Sil-Pad K-10 at 50 psi2.01 °C/WBergquist Sil-Pad K-10 data sheet
TO-247, flat, greased0.24 °C/WIRFP250N data sheet (0.24 typ)

Heatsink selection: what goes wrong in practice

Heatsink θSA is not one number. In natural convection it gets better as the heatsink gets hotter, so read the maker’s curve of temperature rise against power at your own operating point, and use the airflow and orientation it was measured with. The ambient to enter is the air around the heatsink, which inside an enclosure is often well above the room.

Many power packages have the tab connected to a terminal, so a shared or grounded heatsink needs an insulator, and that costs thermal budget, as the mica example shows. Follow the mounting note for the package, keep the compound thin (Nexperia warns that excess can be worse than none) and keep the surfaces flat and clean.

This heatsink calculation is steady state, so short pulses need the part’s transient thermal impedance curve. It also assumes all the heat goes through the heatsink. TI’s SPRA953 says that holds best when θJC is small compared with θJA, as on a tab-mounted power package. On a plastic IC with a stick-on heatsink, part of the heat still leaves through the board, and SPRA953’s Equation 6 is the better approximation.

Glossary

θSA
Heatsink-to-ambient thermal resistance, in °C/W. Lower is a better heatsink.
θCS
Case-to-sink thermal resistance of the interface: grease, pad, or insulator.
θJC
Junction-to-case thermal resistance of the part, to its mounting surface.
Tj max
The highest junction temperature the part is rated for, from Absolute Maximum Ratings.
Thermal interface material
Grease, a pad or phase-change film that fills the air gaps between the case and heatsink.
Mica insulator
A thin mineral washer that electrically isolates a metal tab from the heatsink, usually with compound on both sides.

Related guides

Frequently asked questions

How do you calculate heatsink size?

The heatsink formula gives the thermal resistance you need: θSA = (Tj − Ta) ÷ P − θJC − θCS. For 15 W, a 150 °C junction limit, 40 °C air, θJC of 1.5 °C/W and greased mounting at 0.5 °C/W, that is 5.33 °C/W. This heatsink size calculator gives the θSA to shop for rather than dimensions, so pick a heatsink with θSA at or below that figure at your power.

What does a negative heatsink thermal resistance mean?

That no heatsink can meet the limit: θJC and the interface alone already use up the budget. An IRFZ44N with grease at 40 °C ambient and a 175 °C limit tops out at 67.5 W, even on a perfect heatsink. Lower the power, share it across parts or choose a package with a lower θJC.

Do I need a heatsink at all?

Work out Ta + P × θJA. If that is comfortably below your junction limit, the bare part may be enough. Remember that θJA comes from a test setup, so leave room or measure the result.

How much does thermal paste help on a TO-220?

Nexperia’s figures for a TO-220 are 1.4 °C/W dry and 0.5 °C/W with compound on a screw mount. At 15 W, that is 13.5 °C cooler. Use a thin layer: too much compound can be worse than none.

What is the thermal resistance of a mica insulator?

For a TO-220 on a screw, Nexperia lists 1.4 °C/W for 0.05 mm mica with compound, insulated to 500 V, and 3 °C/W without compound. Using it dry roughly doubles the resistance.

Which θJC do I use for a TO-220?

The value to the surface that touches the heatsink, which is the metal tab. Some data sheets list a top and a bottom value: for a TO-220 tab, use the bottom one. The LM7805 data sheet lists 16.7 °C/W to the top, 1.7 °C/W to the tab, and 4 °C/W in a separate note.

Should I design to the datasheet Tj max?

No. It is a limit, and it is the value at which the part stops being within its ratings. Enter a lower value to keep margin for hot days, part spread and heatsink tolerance.

How do you select a heatsink?

Find the highest θSA you can accept, then read the maker’s curve of temperature rise against power at your own operating point, using the airflow and orientation it was measured with. The heatsink you pick must be at or below that θSA at your power.

Can I use this as a TO-220 heatsink calculator?

Yes. The mounting list covers TO-220 and TO-247 parts, and example 1 uses it as a MOSFET heatsink calculator for an IRFZ44N. For the power figure on a switching MOSFET, use the MOSFET power loss calculator.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.