NewAI Part GeneratorFree to get started
FREE TOOL

PCB trace fusing current calculator

Estimate the current that melts a PCB trace or copper wire in a given time, how long a fault current takes, or the smallest conductor that survives it. This PCB trace fusing current calculator uses the Onderdonk and Preece equations and flags where they stop being valid.

Solve for
Examples
Conductor
Dimensions in
mil
s
°C

Before the overcurrent: ambient plus any normal self-heating.

°C

1083 °C is the melting point as Brooks publishes it (Adam uses 1085 °C, under 0.1 % different in current). Enter a lower limit to see when the copper reaches it.

Current to fuse in 1 s

25.8 A

Preece estimate (no time term)
15.6 A
Cross-section
0.0889 mm² 138 sq mil, 175 cmil
I²t to fuse
667 A²s
Current density
290 A/mm²

⚠ This is an estimate of when copper melts, not a current rating, and it has no safety margin. Size traces for continuous current with a temperature-rise method (IPC-2152), and read this number to one significant figure.

⚠ Board cooling already matters at this time. Brooks and Adam's simulated traces on FR-4 fused at 1.63 to 3.87 times the Onderdonk current at 1 s, so a real trace takes more current, or more time, to open.

The time is when the copper reaches its melting point. Actually opening takes longer, because the heat of fusion is not in the equation.

Estimated fusing current against time
101001m10m100m110100Time (s)Current (A)1 s
OnderdonkOnderdonk past 10 s (not valid)Preece (no time term)

Onderdonk current for this trace

TimeCurrentNo-cooling assumption
1 ms817 AReasonable
10 ms258 AReasonable
100 ms81.7 AReasonable
500 ms36.5 ABreaking down: real current is 1.51 to 3.46 times this
1 s25.8 ABreaking down: real current is 1.63 to 3.87 times this
2 s18.3 ABreaking down: real current is 1.82 to 4.65 times this
5 s11.5 ABreaking down: real current is 2.2 to 6.3 times this
10 s8.17 ABreaking down: real current is higher

What is the fusing current formula for a PCB trace?

Onderdonk’s equation gives I = A × √(log10((Tm − Ta) / (234 + Ta) + 1) / (33 t)), with A in circular mils. A 10 mil wide, 1 oz copper trace is estimated to reach its melting point in 100 ms at about 8.2 A, and in 1 s at about 2.6 A. This is a melt estimate with no margin, not a current rating, and it ignores cooling, so real traces on FR-4 can take 1.5 to 6 times more before they open.

Fusing current formula: Onderdonk and Preece equations

Onderdonk’s equation solves the heating of copper by a constant current, including the rise of resistance with temperature, and assumes no heat escapes.

I = A × √( log10((Tm − Ta) ÷ (234 + Ta) + 1) ÷ (33 × t) )
I
current in A
A
copper cross-section in circular mils
t
time in s
Tm
final temperature in °C (1083 °C for melting copper)
Ta
starting copper temperature in °C

For a trace, the area in circular mils is the width times the thickness (both in mils) times 4/π. Starting from 20 °C and going to 1083 °C the bracket is a constant, 0.0217, so the time for a given current is:

t = 0.0217 × (A ÷ I)²

Preece’s law for copper has no time term. It was fitted to wires in free air, with d the diameter in inches. For a trace, use the diameter of a round wire of the same area, which gives the second form with A in square inches:

I = 10244 × d^1.5     I = 12277 × A^0.75

Worked examples

Example 1: a 10 mil signal trace in a 100 ms fault

1 oz copper is 1.38 mil thick, so A = 10 × 1.38 × 4/π = 17.5 circular mils. With t = 0.1 s and a 20 °C start, I = 17.5 × √(0.0217 ÷ 0.1) = 8.2 A. For a 1 s fault the equation gives about 2.6 A, but treat that as a lower bound: by 1 s the board is pulling heat away, and Brooks and Adam’s simulated 1 oz traces took at least twice the Onderdonk current to fuse.

Example 2: how long a 100 mil trace lasts at 15 A

A = 100 × 1.38 × 4/π = 175 circular mils, so t = 0.0217 × (175 ÷ 15)² = 3 s. Preece’s estimate for the same cross-section is 16 A. The two agree in size, but at this time the board is already pulling heat away, so a real trace lasts longer. An IPC-2152 based calculation for 15 A on this trace, which includes cooling, gives about 180 °C.

Example 3: a trace that has to survive 20 A for 5 s

A = 20 × √(5 ÷ 0.0217) = 304 circular mils. In 1 oz copper that is 173 mil (4.4 mm) wide, with no margin. Derate it for a real design: this is the width that just reaches the melting point after 5 s.

PCB trace fusing current by width and copper weight

Onderdonk estimate for 1 s, starting at 20 °C. These are lower bounds: Brooks and Adam’s simulated traces on FR-4 fused at 1.63 to 3.87 times the equation at 1 s. Multiply by 3.16 for 100 ms, or by 0.45 for 5 s.

Width0.5 oz1 oz2 oz3 oz
6 mil (0.15 mm)775 mA1.55 A3.1 A4.65 A
10 mil (0.25 mm)1.29 A2.58 A5.16 A7.75 A
20 mil (0.51 mm)2.58 A5.16 A10.3 A15.5 A
50 mil (1.3 mm)6.46 A12.9 A25.8 A38.7 A
100 mil (2.5 mm)12.9 A25.8 A51.6 A77.5 A
200 mil (5.1 mm)25.8 A51.6 A103 A155 A

Wire fusing current by AWG

Onderdonk at three durations, and Preece. For wire in air, the no-cooling assumption only holds for short times, about 0.1 s for a 0.2 mm wire and about 1 s for a 2 mm wire.

AWGDiameterArea10 ms100 ms1 sPreece
300.255 mm0.0509 mm²148 A46.8 A14.8 A10.3 A
280.321 mm0.081 mm²235 A74.4 A23.5 A14.6 A
260.405 mm0.129 mm²374 A118 A37.4 A20.6 A
240.511 mm0.205 mm²595 A188 A59.5 A29.2 A
220.644 mm0.326 mm²945 A299 A94.5 A41.3 A
200.812 mm0.518 mm²1.5 kA475 A150 A58.5 A
181.02 mm0.823 mm²2.39 kA756 A239 A82.9 A
161.29 mm1.31 mm²3.8 kA1.2 kA380 A117 A
141.63 mm2.08 mm²6.04 kA1.91 kA604 A166 A
122.05 mm3.31 mm²9.61 kA3.04 kA961 A235 A
102.59 mm5.26 mm²15.3 kA4.83 kA1.53 kA333 A

What goes wrong in practice

Use these numbers to check whether a short fault can open a trace before the upstream fuse or current limit acts, by comparing the time here with the protection’s clearing time or its I²t. Do not use them to set a current rating: that comes from a temperature-rise method such as IPC-2152, and the trace width calculator linked below.

Real traces fuse at their weakest spot, so a narrow neck, a pad transition or an etched-thin section sets the result, not the nominal width. Heat flows into the board quickly: across six simulated traces, Brooks and Adam found the fusing current was 1.51 to 3.46 times the Onderdonk figure at 0.5 s and 2.2 to 6.3 times at 5 s, with narrower traces gaining the most. A plane 12 mil under the trace extended the fusing time by 33 % to over 100 %. Outer layers usually gain plating, so use the finished thickness. The equation also stops at the onset of melting, without the heat of fusion, and it assumes constant DC. For a pulse that is not rectangular, compare its ∫i²dt with the I²t the calculator shows.

A trace that has fused has failed destructively. The heat can damage the laminate and neighboring parts even where it looks intact, so the board should come out of service rather than be repaired.

Glossary

Fusing current
The current that brings a conductor to its melting point in a stated time.
Circular mil
The area of a circle one mil in diameter. A round wire’s area in circular mils is its diameter in mils, squared; one square mil is 1.273 circular mils.
Adiabatic
With no heat exchanged with the surroundings. Onderdonk’s equation assumes the conductor keeps all its heat.
I²t
Current squared times time, a measure of the heating energy of a pulse. Fuses are rated by it, and the Onderdonk model gives a fixed I²t for a given conductor area.
Heat of fusion
The extra energy needed to turn solid copper at its melting point into liquid. The equation stops before this step.
Copper weight
Foil thickness given as ounces of copper per square foot. 1 oz is about 35 µm, or 1.38 mil.

Related guides

Frequently asked questions

What is the fusing current of a PCB trace?

The current that heats the copper to its melting point (1083 °C in the published equation) in a given time. It depends on the cross-section and on the time: a 10 mil, 1 oz trace is estimated at 8.2 A for 100 ms and 2.6 A for 1 s.

What is the Onderdonk equation?

The Onderdonk formula is I = A × √(log10((Tm − Ta) / (234 + Ta) + 1) / (33 t)), with I in amps, A in circular mils, t in seconds and temperatures in °C. It is the analytic solution for a copper conductor heated by a constant current with no cooling at all. The earliest known reference to it is a 1928 General Electric Review article.

What is the Preece equation?

I = 10244 × d^1.5 for copper, with d in inches. W. H. Preece fitted it to experiments on wires in air in the 1880s. It has no time term, so it is a single rough figure for a sustained overcurrent.

How accurate are these equations for traces on a PCB?

Only roughly, and they err low. Brooks and Adam report board cooling taking over in under 1.5 s: their simulated traces on FR-4 fused at 1.63 to 3.87 times the Onderdonk current at 1 s and 2.2 to 6.3 times at 5 s. They still treat it as a usable estimate out to 4 or 5 s, and Adam advises reading the result to one significant figure.

Can a PCB trace be used as a fuse?

Only as a last-resort, one-time failure. The current needed to open a trace is uncertain by the factor above, and the event can damage the laminate and nearby parts, so the board should be replaced. Where a fuse is really needed, use a fuse component with a rated I²t.

Why is the fusing current so much higher than the trace width calculator gives?

They answer different questions. A trace width calculator sets a safe continuous current for a small temperature rise, often 10 to 20 °C. Fusing current is the point of destruction, with no margin, and the laminate is damaged well before the copper melts.

Does ambient temperature change the fusing current?

A little. The equation uses the starting copper temperature, so a trace already running at 85 °C fuses at 92.8 % of the current of one starting at 20 °C.

How do you calculate the fusing current of a copper wire?

Use the same Onderdonk equation with the wire’s area in circular mils, which is its diameter in mils squared. To use this as a wire fusing current calculator, choose an AWG gauge or a diameter: 20 AWG is estimated at 480 A for 100 ms. In air the no-cooling assumption only holds for short times, about 0.1 s for a 0.2 mm wire and about 1 s for a 2 mm wire.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.