What through-hole pad size do I need?
Hole = largest lead + 0.25, 0.20 or 0.15 mm (Levels A, B, C), and pad = largest hole + 2 × 0.05 mm + 0.4, 0.25 or 0.2 mm. For a 0.6 mm lead at Level B that is a 0.8 mm hole and a 1.15 mm pad, or 0.9 mm and 1.35 mm once a ±0.08 mm hole tolerance is allowed for.
Through-hole pad size formula
IPC-2222 sets a window for the hole relative to the lead. IPC-2221 then sizes the land from the largest hole the fab can deliver.
Hmin = Lmax + A₁ Hmax = Lmin + A₂
- Hmin
- smallest finished hole allowed
- Hmax
- largest finished hole allowed
- Lmax, Lmin
- largest and smallest lead dimension, from the datasheet
- A₁
- 0.25 mm (Level A), 0.20 mm (Level B), 0.15 mm (Level C)
- A₂
- 0.7 mm (Levels A and B), 0.6 mm (Level C)
For a rectangular lead, use the diagonal as the lead dimension:
Lead = √(width² + thickness²)
The land is sized from the largest hole, with T the ± hole tolerance:
L = a + 2b + c
- L
- minimum land diameter
- a
- largest finished hole (hole + T)
- b
- minimum annular ring, 0.05 mm on external layers
- c
- 0.4 mm (Level A), 0.25 mm (Level B), 0.2 mm (Level C)
The allowance c grows by 0.05 mm for boards with more than 8 layers and by 0.05 mm per ounce of copper above 1 oz. That figure is as I-Connect007 gives it. Altium's guide prints 20 mil for the same rule, which we read as a typo, since that is 0.51 mm, more than any allowance c in the table. IPC-2221 is a paid document we did not read directly, so check section 9.1.1 if this margin matters.
Worked examples
Example 1: a 1/4 W axial resistor, 0.6 mm lead, Level B
The largest lead is 0.6 mm and the smallest 0.5 mm. The minimum hole is 0.8 mm. Adding ±0.08 mm and rounding up gives a 0.9 mm hole, up to 0.98 mm as delivered, within the 1.2 mm limit. The land is 1.33 mm, so use a 1.35 mm pad, a 0.225 mm drawn ring.
Example 2: a 0.64 mm square header pin, Level B
The diagonal is 0.9051 mm (35.6 mil). The minimum hole is 1.105 mm, so a 1.2 mm hole after tolerance and rounding, with a 1.65 mm pad.
Example 3: a 1N4007 diode at all three levels
The lead is 0.71 to 0.86 mm. Level A: 1.2 mm hole, 1.8 mm pad. Level B: 1.15 mm hole, 1.6 mm pad. Level C: 1.1 mm hole, 1.5 mm pad. Level C leaves the smallest ring, 0.2 mm, and the highest demand on the assembly process.
IPC through-hole pad size allowances by level
The three constants behind every result on this page, in mm.
| Level | Min hole over max lead | Max hole over min lead | Fabrication allowance c | Pad over hole (b = 0.05) |
|---|
| Level A | 0.25 | 0.70 | 0.40 | 0.50 |
| Level B | 0.20 | 0.70 | 0.25 | 0.35 |
| Level C | 0.15 | 0.60 | 0.20 | 0.30 |
Through-hole pad dimensions for common leads
Largest lead from the datasheet, with a ±0.08 mm hole tolerance and 0.05 mm rounding. Hole / pad in mm.
| Lead | Size | Effective | Level A | Level B | Level C | Source |
|---|
| 1N4148 diode (DO-35) | 0.55 mm round | 0.550 | 0.9 / 1.5 | 0.85 / 1.3 | 0.8 / 1.2 | Vishay |
| 1/4 W resistor (Yageo MFR-25) | 0.60 mm round | 0.600 | 0.95 / 1.55 | 0.9 / 1.35 | 0.85 / 1.25 | Yageo |
| 1N4007 diode (DO-41) | 0.86 mm round | 0.860 | 1.2 / 1.8 | 1.15 / 1.6 | 1.1 / 1.5 | Vishay |
| 2.54 mm header pin | 0.64 mm square | 0.905 | 1.25 / 1.85 | 1.2 / 1.65 | 1.15 / 1.55 | CJT |
| 8-pin ceramic DIP (TI JG0008A) | 0.58 × 0.36 mm | 0.683 | 1.05 / 1.65 | 1 / 1.45 | 0.95 / 1.35 | TI |
| TO-220 lead | 1.01 × 0.61 mm | 1.180 | 1.55 / 2.15 | 1.5 / 1.95 | 1.45 / 1.85 | Diodes Inc. |
The 1N4007 row uses Vishay's standard DO-41 lead, 0.71 to 0.86 mm. Vishay's drawing notes a thinner lead for part numbers with suffix E, 0.58 to 0.66 mm. Sized for its own lead at Level B, a suffix E part takes a 0.95 mm hole and a 1.4 mm pad. In the standard part's 1.15 mm hole it still fits, with up to 1.23 mm delivered against a Level B limit of 1.28 mm.
PCB hole size and pad size by lead diameter
The bare formula, with no hole tolerance and no rounding. Hole / pad in mm.
| Lead | Level A | Level B | Level C |
|---|
| 0.4 | 0.65 / 1.15 | 0.60 / 0.95 | 0.55 / 0.85 |
| 0.5 | 0.75 / 1.25 | 0.70 / 1.05 | 0.65 / 0.95 |
| 0.6 | 0.85 / 1.35 | 0.80 / 1.15 | 0.75 / 1.05 |
| 0.7 | 0.95 / 1.45 | 0.90 / 1.25 | 0.85 / 1.15 |
| 0.8 | 1.05 / 1.55 | 1.00 / 1.35 | 0.95 / 1.25 |
| 0.9 | 1.15 / 1.65 | 1.10 / 1.45 | 1.05 / 1.35 |
| 1.0 | 1.25 / 1.75 | 1.20 / 1.55 | 1.15 / 1.45 |
| 1.2 | 1.45 / 1.95 | 1.40 / 1.75 | 1.35 / 1.65 |
| 1.4 | 1.65 / 2.15 | 1.60 / 1.95 | 1.55 / 1.85 |
| 1.6 | 1.85 / 2.35 | 1.80 / 2.15 | 1.75 / 2.05 |
Choosing a pad in practice
Use the largest lead dimension in the datasheet, not the nominal, and the smallest for the upper hole limit. A hole that is too tight will not wet or fill well, and one that is too loose leaves a weak joint and drops parts during wave soldering. The IPC figures give a minimum pad, which is often smaller than what hand soldering or rework needs: fabs commonly ask for more ring than the standard, so check their minimum. Large leads and thermal loads need bigger pads than the formula suggests. Connectors with press-fit or board-lock features have their own hole specification in the datasheet, and that takes priority over all of this.
Glossary
- Finished hole
- The hole diameter after plating, which is what the lead has to fit.
- Producibility level
- IPC grade A, B or C describing how tight a design is to build.
- Annular ring
- The copper band around the hole, from the hole wall to the edge of the pad.
- Fabrication allowance
- The extra pad diameter IPC-2221 adds for process variation, the c in L = a + 2b + c.
- Effective lead diameter
- The lead dimension that sets the hole: the diameter of a round lead, or the diagonal of a rectangular one.
- PTH pad size
- The copper land diameter of a plated through-hole (PTH) part, set from the largest finished hole, the annular ring and the fabrication allowance.
Frequently asked questions
How do you calculate through-hole pad size?
Take the largest lead diameter, add the IPC-2222 hole allowance to get the minimum hole, then apply L = a + 2b + c from IPC-2221. For a 0.6 mm lead at Level B with no hole tolerance that is a 0.8 mm hole and a 1.15 mm pad.
What hole size do I need for a 0.6 mm lead?
IPC-2222 asks for at least 0.85 mm, 0.8 mm or 0.75 mm at Levels A, B and C. With a ±0.08 mm hole tolerance, Level B becomes 0.9 mm after rounding up to a 0.05 mm drill step.
What are IPC Levels A, B and C?
They are producibility levels. Level A is general design, the easiest to build, with the most clearance. Level B is moderate, and Level C is high density, with the tightest fit and the smallest pad.
How do I size the hole for a rectangular or square lead?
Use the diagonal, since the corners set whether the lead fits. A 0.64 mm square pin has a 0.9051 mm diagonal, so Level B needs a hole of at least 1.105 mm.
What annular ring do through-hole pads need?
IPC-2221 uses a 0.05 mm minimum ring on external layers in the land formula, plus the fabrication allowance. JLCPCB recommends 0.25 mm or more on 2-layer boards. The default example here gives a 0.225 mm drawn ring.
Is the hole in the footprint the drill size or the finished size?
These formulas give the finished hole, after plating. The fabricator normally drills 0.1 to 0.15 mm larger to allow for plating and adds that itself, so give the finished size in your drill table unless your fab says otherwise.
What is IPC-7251?
It was the planned land pattern standard for through-hole parts. According to PCB Libraries, the IPC committee merged it into IPC-7351C. Hole and land calculations in practice still come from IPC-2222 and IPC-2221.
Is this a PCB pad size calculator or a PCB hole size calculator?
Both, for through-hole parts. It finds the finished hole from the lead first, then the pad from the largest hole: a 0.6 mm lead at Level B with a ±0.08 mm hole tolerance comes out at a 0.9 mm hole and a 1.35 mm pad.
More free PCB tools
See all free electronics tools →
- Solder stencil area ratio calculatorArea ratio and aspect ratio of a solder paste stencil aperture, and the thickest stencil that will still release paste.
- Annular ring calculatorAnnular ring from pad and drill size, the worst case after drill tolerance and registration, and the minimum pad for IPC class 2 or 3.
- PCB trace resistance calculatorResistance, voltage drop and power loss of a PCB trace from its width, length, copper weight and temperature.
- PCB trace spacing calculator (IPC-2221)Minimum conductor spacing for a voltage from the IPC-2221 table, for internal, coated and uncoated external layers.
- Online KiCad design checkerUpload a KiCad project to run KiCad 10 DRC, ERC and schematic parity, plus JLCPCB or PCBWay rules. Every finding links to its fix.
- PCB trace fusing current calculatorCurrent that melts a PCB trace or wire in a given time, using the Onderdonk and Preece equations.
Design the whole board, not one number
ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.