NewAI Part GeneratorFree to get started
FREE TOOL

Solder stencil area ratio calculator

A solder paste aperture has to clear the IPC-7525 area and aspect ratio limits. This stencil area ratio calculator checks both, then finds the thickest foil an aperture can use or the smallest aperture a foil can print, for rectangular and round openings in mm or mil.

Solve for
Examples
Units
Aperture shape
mm
mm
µm

Area ratio

0.715

minimum 0.66

Aspect ratio
1.84 minimum 1.5
Result
Passes both rules
Thickest stencil for this aperture
135 µm 5.33 mil, set by the area ratio
Opening area
0.184 mm²
Wall area
0.258 mm²
Paste volume at 100 % transfer
0.023 mm³

Assumes straight walls and a filled aperture. These ratios predict paste release only; check solder volume and bridging separately.

Area ratio and aspect ratio against foil thickness
00.511.5201234550100150200250Foil thickness (µm)Area ratioAspect ratioArea ratio 0.66Aspect 1.5T 125 µmTmax 135 µm
Area ratioAspect ratio

This aperture on common foils (the thickest that passes is highlighted)

FoilArea ratioAspect ratioResult
80 µm (3.1 mil)1.122.88Pass
100 µm (3.9 mil)0.8932.3Pass
120 µm (4.7 mil)0.7441.92Pass
130 µm (5.1 mil)0.6871.77Pass
150 µm (5.9 mil)0.5951.53Fails area ratio
180 µm (7.1 mil)0.4961.28Fails both
200 µm (7.9 mil)0.4471.15Fails both

What is the stencil area ratio formula?

Area ratio = (L × W) ÷ (2 × (L + W) × T), the aperture opening divided by the area of its walls. A 0.80 × 0.23 mm QFN aperture in a 125 µm foil has an area ratio of 0.715, above the IPC-7525 minimum of 0.66, and an aspect ratio W ÷ T of 1.84, above the minimum of 1.5.

Stencil area ratio and aspect ratio formulas

When the stencil lifts off the board, paste is pulled toward the pad by its contact with the pad and held back by its contact with the aperture walls. The area ratio compares those two surfaces.

Area ratio = (L × W) ÷ (2 × (L + W) × T) ≥ 0.66
L, W
aperture length and width (W is the narrow side)
T
stencil foil thickness, in the same unit
Aspect ratio = W ÷ T ≥ 1.5

A round aperture of diameter D, and a square of side D, both reduce to:

Area ratio = D ÷ (4 × T)

Solved for the thickest foil, and for the narrowest slot of a given length (A is the minimum area ratio):

Tmax = min( (L × W) ÷ (2 × (L + W) × A), W ÷ 1.5 )
Wmin = max( 2 × A × T × L ÷ (L − 2 × A × T), 1.5 × T )

Worked examples

Example 1: a 0.5 mm pitch QFN lead in a 125 µm foil

TI's QFN note uses a 0.80 × 0.23 mm aperture. The opening is 0.184 mm² and the walls are 0.2575 mm², so the area ratio is 0.715. The aspect ratio is 0.23 ÷ 0.125 = 1.84. Both limits pass.

Example 2: the thickest foil for a small 0201 pad

A 0.32 × 0.24 mm aperture (IEC 61188-6-2 pad, 1:1) allows 104 µm by the area ratio and 160 µm by the aspect ratio. The area ratio governs, so the limit is 104 µm and the thickest common foil is 100 µm.

Example 3: the smallest round aperture in a 100 µm foil

The area ratio needs D ≥ 4 × 0.66 × 0.1 = 0.264 mm; the aspect ratio only needs 0.15 mm. The smallest opening is 0.264 mm.

Stencil thickness for 0402, 0201 and QFN pads

Apertures 1:1 with the pad unless stated. Chip pads are from Vishay's reflow recommendations; QFN sizes are TI's 0.5 mm pitch example. The foil columns show the area ratio at that thickness.

ApertureL × W (mm)100 µm120 µm130 µmThickest foil
0402 chip (1005 metric), IPC-7351 pad0.60 × 0.551.431.21.1217 µm
0402 chip (1005 metric), IEC 61188-6-2 pad0.55 × 0.351.070.8910.823162 µm
0201 chip (0603 metric), IPC-7351 pad0.43 × 0.421.060.8850.817161 µm
0201 chip (0603 metric), IEC 61188-6-2 pad0.32 × 0.240.6860.571 (fails)0.527 (fails)104 µm
0.5 mm pitch QFN lead, 1:1 with the pad0.85 × 0.281.050.8780.81160 µm
0.5 mm pitch QFN lead, reduced aperture0.80 × 0.230.8930.7440.687135 µm

Smallest stencil aperture for each foil thickness

Limits of 0.66 for the area ratio and 1.5 for the aspect ratio. On a square or round opening the area ratio governs. On a long slot it approaches W ÷ (2T), so the aspect ratio takes over once L is more than about 7.3 × W.

FoilRound or squareSlot, 1 mm longSlot, 3 mm long
80 µm0.211 mm0.12 mm0.12 mm
100 µm0.264 mm0.152 mm0.15 mm
120 µm0.317 mm0.188 mm0.18 mm
130 µm0.343 mm0.207 mm0.195 mm
150 µm0.396 mm0.247 mm0.225 mm
180 µm0.475 mm0.312 mm0.27 mm
200 µm0.528 mm0.359 mm0.3 mm

What the ratios do not tell you

These two numbers predict paste release and nothing else. A passing aperture can still bridge at fine pitch, so TI suggests reducing the aperture by 20 % at 0.5 mm pitch and below when placement force is poorly controlled, while keeping the ratios within limits. Large exposed pads are the opposite case: TI typically covers only 50 to 70 % of the pad, because a 1:1 print can float the part. The 0.66 limit came from work with Type 3 paste. Finer powder helps only a little (the Speedline and Indium study reached 0.58), so for very small parts a thinner foil or a step-down area is usually more effective than changing the paste.

Glossary

Aperture
The opening cut in the stencil foil that sets the size and position of a paste deposit.
Area ratio
The aperture opening area divided by the area of its walls. It predicts how well paste releases.
Aspect ratio
The narrow side of the aperture divided by the foil thickness.
Foil thickness (T)
The thickness of the stencil sheet, commonly 100 to 200 µm.
Transfer efficiency
The paste volume deposited on the pad as a percentage of the aperture volume.
Powder type
A size class of the solder powder in the paste. A higher type number means smaller particles.
Electroformed stencil
A stencil built up from nickel by plating, with smoother walls than a laser-cut one.

Related guides

Frequently asked questions

What is a good area ratio for a solder stencil?

0.66 or higher, the IPC-7525 minimum for stainless foil with Type 3 paste. Higher is better: transfer efficiency rises and its spread falls as the area ratio goes up.

What is the difference between stencil area ratio and stencil aspect ratio?

Area ratio compares the opening with the wall area around it: (L × W) ÷ (2 × (L + W) × T). Aspect ratio compares the narrow side with the foil thickness: W ÷ T, with a minimum of 1.5. Area ratio is the stricter rule for square and round openings; aspect ratio can govern on long, narrow slots.

How do you calculate the area ratio of a round aperture?

D ÷ (4 × T), because the opening is πD²/4 and the wall is πD × T. A square opening of side W gives the same result with W in place of D, so a 0.264 mm square in a 100 µm foil has an area ratio of 0.66.

What stencil thickness should I use for 0402 and 0201 parts?

It depends on the pad. A 0402 pad of 0.60 × 0.55 mm (IPC-7351) can use a foil up to 217 µm, so any common foil passes. A small 0201 pad of 0.32 × 0.24 mm (IEC 61188-6-2) is limited to 104 µm, so a 100 µm foil is the practical choice.

What stencil thickness is used for a 0.5 mm pitch QFN?

TI recommends 0.125 mm as a guide for QFN and SON parts. Its example aperture of 0.80 × 0.23 mm gives an area ratio of 0.715 at that thickness, and the aperture stays within limits up to 135 µm.

Can an area ratio below 0.66 still print?

Sometimes. A Speedline and Indium study found 0.58 kept transfer above 90 % with Type 4 and Type 5 paste, and TI reports nickel-formed stencils printing down to 0.57. Check with your stencil supplier and expect less margin.

Does reducing the aperture change the area ratio?

Yes, a smaller opening lowers it. TI's 0.5 mm pitch example goes from 0.842 at 1:1 (0.85 × 0.28 mm) to 0.715 when reduced to 0.80 × 0.23 mm in a 125 µm foil, so recheck the ratio after any reduction.

How do I calculate solder paste stencil thickness?

Use the Thickest stencil mode as a stencil thickness calculator. The limit is the smaller of (L × W) ÷ (2 × (L + W) × 0.66) and W ÷ 1.5, so a 0.32 × 0.24 mm aperture allows up to 104 µm and the thickest common foil is 100 µm.

What does a stencil aperture calculator check?

The two IPC-7525 stencil design limits: an area ratio of at least 0.66 and an aspect ratio of at least 1.5. Passing both predicts paste release and nothing else, so a passing aperture can still bridge at fine pitch.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.