NewAI Part GeneratorFree to get started
FREE TOOL

PCB trace inductance calculator

A PCB trace inductance calculator needs to know the return path, so pick yours: a ground plane under the trace, two planes around it, or no nearby return. Compare the three, and see the reactance at any frequency and the voltage a fast current edge develops across it.

Return path
Examples
Units
mm
mm
mm

Dielectric from the trace to the plane. On the No nearby plane tab it only sets the comparison.

Hz

Optional.

Loop inductance

8.733 nH

Inductance per mm
0.349 nH/mm 8.87 nH/in
Reactance at 100 MHz
5.487 Ω
DC resistance at 25 °C
50.23 mΩ
Reactance equals resistance at
915.4 kHz DC resistance, ignoring skin effect
Voltage for a 1 A/ns edge
8.733 V L × di/dt
Same trace, no nearby plane
28.35 nH

Assumes a continuous plane directly under the trace carrying the return current. A slot or gap in the plane forces a longer return path and adds inductance. Ignores end effects and internal inductance of the copper.

Inductance against trace length
1n10n100n5102050100200Trace length (mm)Inductance (H)25 mm
Over a planeNo nearby plane

Comparison of return paths

Return pathInductancePer mmReactance at 100 MHz
No nearby plane28.3 nH1.13 nH/mm17.8 Ω
Over a plane8.73 nH0.349 nH/mm5.49 Ω

How do you calculate trace inductance on a PCB?

It depends on where the return current flows. Over a ground plane, inductance per length is the impedance of the air-filled line divided by the speed of light: a 25 mm long, 0.25 mm wide trace 0.2 mm above a plane is about 8.73 nH. With no nearby return, the same trace has a partial inductance of about 28.3 nH, from L = 2l × [ln(2l ÷ (w + t)) + 0.5 + 0.2235 × (w + t) ÷ l] nH, with l in cm.

PCB trace inductance formulas

Inductance is a property of a current loop, so the answer depends on the return path. There are two useful cases: a trace on its own, and a trace with a plane carrying the return.

No nearby return. Rosa's formula for the partial self-inductance of a straight rectangular bar:

L = 2l × [ ln(2l ÷ (w + t)) + 0.5 + 0.2235 × (w + t) ÷ l ]
L
partial self-inductance in nH
l, w, t
trace length, width and copper thickness in cm

Over one plane (microstrip) or centered between two (stripline), the field is a transmission-line field. Inductance per length follows from the characteristic impedance of the same line with the dielectric removed:

L′ = Z₀ₐ ÷ c = Z₀ × √ε_eff ÷ c
L′
inductance per length in H/m
Z₀ₐ
characteristic impedance of the air-filled line in Ω
c
speed of light, 299,792,458 m/s
ε_eff
effective permittivity of the real line

Z₀ₐ comes from the Hammerstad and Jensen model for microstrip, and for stripline from H. A. Wheeler, Transmission-Line Properties of a Strip Line Between Parallel Planes, IEEE Trans. MTT-26(11), 1978. These are the same models as the PCB impedance calculator. The reactance at frequency f is:

XL = 2π × f × L

Worked examples

Example 1: a 25 mm signal trace on a 4-layer board

A 0.25 mm wide trace in 1 oz copper, 0.2 mm above its plane, has an air-filled impedance of 105 Ω, so L′ = 0.349 nH/mm and the whole trace is 8.73 nH. At 100 MHz that is 5.49 Ω.

Example 2: the same trace with no nearby plane

With l = 2.5 cm and w + t = 0.0285 cm, L = 2 × 2.5 × [ln(175.4) + 0.5 + 0.0025] = 28.3 nH, about 3.2 times the value over a plane.

Example 3: a short decoupling stub

A 5 mm long, 0.5 mm wide stub, 0.1 mm above the plane, is 780 pH. A 1 A/ns edge through it develops 780 mV, and a similar stub on the other side of the capacitor doubles that. Keep decoupling stubs short and over a close plane.

Example 4: a stripline on an inner layer

A 25 mm long, 0.15 mm wide trace in 0.5 oz copper, centered between planes 0.4 mm apart, is 8.75 nH.

PCB trace inductance per mm over a plane

nH per mm for 1 oz (35 µm) copper, from the air-filled microstrip impedance. Height is the dielectric from trace to plane. The Over a plane tab above is a microstrip inductance calculator for any other width, height or copper weight.

Width \ Height0.1 mm0.2 mm0.4 mm0.8 mm1.6 mm
0.15 mm0.3070.4260.5540.6870.822
0.25 mm0.2390.3490.4750.6070.742
0.5 mm0.1560.2470.3610.490.624
1 mm0.09390.1590.2520.3690.499
2 mm0.05290.0950.1620.2560.374
5 mm0.02310.04370.07980.1390.225

Inductance of PCB traces with no nearby plane

Partial self-inductance in nH for 1 oz copper. It grows slightly faster than length.

Length \ Width0.15 mm0.25 mm0.5 mm1 mm2 mm
5 mm4.54.073.452.812.18
10 mm10.49.518.276.975.66
25 mm30.528.325.221.918.6
50 mm67.963.657.350.844
100 mm150141129115102

Where these models stop

Rosa's formula assumes a long bar with uniform current. Compared with direct integration of Neumann's formula it is within 1 % when the length is at least five times w + t, and within about 5 % down to a length equal to w + t; the calculator warns below five and stops below one. The plane models assume a continuous plane directly under the trace, and they omit end effects and the copper's internal inductance. The stripline thickness correction is least reliable once the copper takes up more than a quarter of the plane spacing, and the calculator warns there. A slot in the plane forces the return current around it and can add far more inductance than the trace itself. Vias, connector pins and component mounting inductance add to the loop too. Once the trace is longer than about a tenth of a wavelength, treat it as a transmission line.

Glossary

Partial inductance
The inductance assigned to one segment of a conductor. Only the sum over a closed loop is physically measurable.
Loop inductance
The inductance of a complete current path, including the return conductor.
Microstrip
A trace on an outer layer with a reference plane on one side.
Stripline
A trace on an inner layer with reference planes on both sides.
Inductive reactance (XL)
The opposition to AC from inductance, 2πfL, in ohms.
Air-filled impedance
The characteristic impedance of a line with the dielectric removed, which sets its inductance per length.

Related guides

Frequently asked questions

How much inductance does a PCB trace have?

It depends on the return path. A 25 mm long, 0.25 mm wide trace is about 8.73 nH over a plane 0.2 mm below it and 28.3 nH with no nearby return. The closer the return current, the lower the inductance.

What is the PCB trace inductance formula?

With no nearby return, L = 2l × [ln(2l ÷ (w + t)) + 0.5 + 0.2235 × (w + t) ÷ l] nH, with dimensions in cm. Over a plane, inductance per length is L′ = Z₀ₐ ÷ c, where Z₀ₐ is the characteristic impedance of the air-filled line. Multiply by the length for the whole trace.

What is the rule of thumb for PCB trace inductance per mm?

About 1 nH per mm for an isolated thin trace (a 10 mm long, 0.25 mm wide trace is 9.51 nH), and roughly a third of that over a plane close beneath it (0.349 nH/mm at 0.2 mm). Use the calculator for your geometry, because neither figure holds for wide traces or thick dielectrics.

Does making a trace wider reduce inductance?

Yes, but slowly when there is no plane, because width enters through a logarithm. Going from 0.25 mm to 1 mm cuts 28.3 nH to only 21.9 nH for a 25 mm isolated trace. Over a plane at 0.2 mm the same change takes 8.73 nH to 3.98 nH.

Does the dielectric constant change trace inductance?

No. Inductance depends on geometry and on magnetic permeability, and PCB laminates are non-magnetic. FR-4 and Rogers give the same inductance for the same dimensions, even though Z0 and delay differ. That is why this calculator has no εr field.

What is the difference between partial and loop inductance?

A loop has a defined inductance; a piece of wire on its own only has a partial inductance. Partial inductance is useful for adding up segments of a loop. Loop inductance equals L(trace) + L(return) − 2M, so a close return conductor cancels most of the partial value.

What is the reactance of a trace at 100 MHz?

XL = 2πfL. The 8.73 nH trace over a plane above is 5.49 Ω at 100 MHz, and it scales linearly with both frequency and inductance.

How does the height above the plane affect inductance?

Closer is lower. The 25 mm, 0.25 mm trace is 5.96 nH at 0.1 mm, 8.73 nH at 0.2 mm and 18.6 nH on the far side of a 1.6 mm board.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.