NewAI Part GeneratorFree to get started
FREE TOOL

PCB propagation delay calculator

Start with your stackup, or an effective Dk from your fab, and this PCB propagation delay calculator returns the signal delay per inch and per millimeter on microstrip and stripline, the velocity factor, and the delay of a trace of any length.

Solve for
Examples
Units
Routing

Use your laminate’s Dk at the signal frequency.

mm
mm
mm

Optional: fill in for a differential pair to use its odd-mode delay.

Copper weight

Delay per mm

5.899 ps/mm

Delay per inch
149.8 ps/in
Velocity
169.5 mm/ns
Velocity factor
0.565 of the speed of light
Effective Dk εeff
3.128
Impedance Z0
54.5 Ω

Hammerstad-Jensen microstrip, quasi-static with copper thickness. Solder mask adds dielectric above the trace, so a masked outer-layer trace is a little slower than this.

Microstrip delay against trace width
5.25.45.65.866.26.46.66.80.10.20.51251020Width / heightDelay (ps/mm)w/h 1.50

What is PCB trace propagation delay?

tpd = √εeff ÷ c. On FR-4 with εr 4.4, a stripline has 177.7 ps per inch (6.997 ps/mm). A 0.3 mm microstrip over 0.2 mm has εeff 3.13, or 149.8 ps per inch. Multiply by the length for the delay of the trace.

PCB propagation delay formula

A signal on a transmission line travels at the speed of light divided by the square root of the effective dielectric constant. Stripline is simple. Microstrip needs a model for how much of the field is in air.

tpd = √εeff ÷ c     delay = tpd × length     velocity factor = 1 ÷ √εeff
tpd
delay per unit length
εeff
effective dielectric constant (equal to εr for stripline)
c
speed of light: 299.79 mm/ns, or 11.80 in/ns

For microstrip, the Hammerstad-Jensen fit gives εeff from u = w ÷ h and εr:

εeff = (εr + 1) ÷ 2 + (εr − 1) ÷ 2 × (1 + 10 ÷ u)^(−a × b)
a
1 + ln[(u⁴ + (u/52)²) ÷ (u⁴ + 0.432)] ÷ 49 + ln[1 + (u/18.1)³] ÷ 18.7
b
0.564 × [(εr − 0.9) ÷ (εr + 3)]^0.053

The calculator also applies Hammerstad-Jensen’s correction for copper thickness, and for pairs the Kirschning-Jansen odd-mode εeff, which reads up to about 2 % slow against a 2-D field solve with ½ oz or 1 oz copper. A common simpler estimate is 1 + q (εr − 1) with q = ½ (1 + 1 ÷ √(1 + 12 h/w)). For a 0.3 mm trace over 0.2 mm it gives 3.27 against 3.13 from the full model with 1 oz copper. Nearly all of that difference is the copper thickness, which the simple formula ignores.

Worked examples

Example 1: a 100 mm stripline in FR-4

tpd = √4.4 ÷ 299.79 mm/ns = 6.997 ps/mm. Over 100 mm the delay is 700 ps, and the velocity factor is 0.477.

Example 2: a 0.3 mm microstrip over 0.2 mm

With w/h = 1.5, εr = 4.4 and 1 oz copper, εeff = 3.13. So tpd = √3.13 ÷ c = 149.8 ps/in (5.899 ps/mm), faster than the stripline above by about 16 %.

Example 3: how long is 1 ns of delay

On the same stripline, length = 1 ns ÷ 6.997 ps/mm = 143 mm (5.63 in).

Stripline propagation delay table by dielectric constant

tpd = √εr ÷ c. Stripline delay depends only on Dk, so this table works for any trace width. For a laminate not listed, enter its Dk in the stripline propagation delay calculator above.

εrMaterialps/inps/mmVelocity factor
4.00FR-4, low end169.56.6710.5
4.20FR-4173.66.8360.488
4.30FR-4175.76.9170.482
4.40FR-4177.76.9970.477
4.50FR-4179.77.0760.471
4.60FR-4, high end181.77.1540.466
3.66RO4350B design Dk162.16.3810.523
3.55RO4003C design Dk159.66.2850.531

Microstrip propagation delay on common stackups

Hammerstad-Jensen εeff for a 50 Ω trace on each stackup, 1 oz copper, no solder mask. For your own width and height, use the microstrip propagation delay calculator above.

Stackup50 Ω widthεeffps/inps/mm
JLCPCB 4-layer 1.6 mm, 7628 prepreg (h 0.2104 mm, εr 4.4)0.372 mm3.19151.35.96
JLCPCB 4-layer, 2116 prepreg (h 0.1164 mm, εr 4.16)0.206 mm2.98146.35.76
JLCPCB 4-layer, 3313 prepreg (h 0.0994 mm, εr 4.1)0.175 mm2.93144.95.71
JLCPCB 4-layer, 1080 prepreg (h 0.0764 mm, εr 3.91)0.135 mm2.78141.45.57
2-layer 1.6 mm FR-4 (h ≈ 1.53 mm, εr 4.6)2.79 mm3.42156.86.17
Rogers RO4350B 0.254 mm / 10 mil (design Dk 3.66)0.523 mm2.771415.55

What changes signal speed on PCB traces

Solder mask adds dielectric above a microstrip and slows it a little. FR-4 Dk depends on resin content and frequency, so use your laminate’s number at the signal frequency, and if the core and prepreg differ on a stripline use a thickness-weighted average. The model is quasi-static, so it does not include dispersion. Each trace of a pair can also see a different mix of glass and resin: TI notes the glass has εr of about 6 and the epoxy about 3, and that the difference can cause skew within a pair. The delay in vias and packages is separate, so add it to the trace delay when the total matters.

Glossary

Propagation delay (tpd)
The time a signal takes to travel a unit length of trace, in ps/in or ps/mm.
Effective dielectric constant (εeff)
The Dk a line behaves as if it had, between 1 and εr on microstrip and equal to εr on stripline.
Velocity factor
Signal speed as a fraction of the speed of light, 1 ÷ √εeff.
Microstrip
A trace on an outer layer over one reference plane, with air above it.
Stripline
A trace on an inner layer between two reference planes, fully embedded in dielectric.
Odd mode
How a differential pair is driven: equal and opposite signals on the two traces.

Related guides

Frequently asked questions

What is the typical FR-4 propagation delay?

About 177.7 ps per inch (6.997 ps/mm) on an inner layer with εr 4.4, and about 149.8 ps per inch (5.899 ps/mm) for a 0.3 mm wide microstrip over 0.2 mm.

How fast does a signal travel on a PCB?

PCB signal speed is the speed of light divided by √εeff. On an inner FR-4 layer with εr 4.4 that is 0.477 of c, or 143 mm per ns (5.63 in per ns). The 0.3 mm microstrip over 0.2 mm runs faster, at 0.565 of c.

Why is microstrip faster than stripline?

Part of a microstrip’s field runs through air, which lowers the effective dielectric constant. A stripline is fully embedded, so εeff equals εr. In the example above that is εeff 3.13 against 4.4.

How do you calculate propagation delay on a PCB?

Multiply the delay per length by the length: tpd = √εeff ÷ c, and delay = tpd × length. A 100 mm stripline in εr 4.4 has 700 ps of delay.

What is velocity factor?

The signal speed as a fraction of the speed of light, 1 ÷ √εeff. For εr 4.4 stripline it is 0.477, and for the example microstrip 0.565.

Does trace width change propagation delay?

Not on stripline, where the delay depends only on Dk. On microstrip it changes slightly: a wider trace keeps more of the field in the dielectric, so it is a little slower. The chart in the calculator shows the effect for your stackup.

How long is a trace with 1 ns of delay?

About 143 mm (5.63 in) on an inner FR-4 layer with εr 4.4. Signals travel at roughly half the speed of light in FR-4.

Is the delay of a differential pair the same as a single trace?

On stripline, yes. On microstrip, the odd-mode signal of a pair is faster because more of its field is in air: a 0.2 mm pair with a 0.2 mm gap over 0.2 mm runs at about 140 ps/in, against about 147 ps/in for one trace alone.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.