NewAI Part GeneratorFree to get started
FREE TOOL

Zener diode calculator (shunt regulator)

This Zener diode calculator sizes the series resistor for a shunt regulator so it keeps regulating at the lowest supply and the heaviest load, then shows the worst-case Zener and resistor power at the other extreme. You can also check an existing resistor or start from Vishay 1N47xxA datasheet values.

Solve for
Examples
V
V
V
%

The A suffix of the 1N47xx series is ±5%.

A

Keep it well above the knee current IZK.

A

Use 0 if the load can be disconnected.

A
Resistor series
W

Optional: Ptot from the datasheet.

A

Optional: maximum regulator current from the datasheet.

Ω

Optional: estimates how much the output moves.

Series resistor

180 Ω

E24, rounded down

Maximum (exact) resistor
185.8 Ω
Zener current, VIN(min) and IL(max)
5.806 mA with VZ 5.355 V
Zener current, VIN(max) and IL(min)
50.86 mA with VZ 4.845 V
Zener power (worst case)
257.2 mW at VZ 5.355 V, 48 mA
Resistor power (worst case)
465.6 mW
Load current at dropout (VIN min)
25.81 mA IZ falls to 0 above this

VZ is specified at the test current IZT. At much lower current the voltage is lower and the slope resistance much higher, so regulation near IZ(min) is loose. Pick a resistor wattage comfortably above the worst case.

Zener current against input voltage with R = 180 Ω (nominal VZ)
010m20m30m40m50m1010.51111.51212.51313.514Input voltage (V)Zener current (A)IZ(min) 5 mA
Load 0 ALoad 20 mA

How do you calculate the series resistor for a Zener diode regulator?

Use R = (VIN(min) − VZ) ÷ (IL(max) + IZ(min)) and round down to a standard value; then check the Zener power at the highest input with the lightest load. A 5.1 V Zener from 10 to 14 V with a 0 to 20 mA load and 5 mA minimum Zener current needs R ≤ 186 Ω, so 180 Ω; the Zener then dissipates up to 257 mW and the resistor 466 mW.

Zener diode formulas for the series resistor, current and power

The series resistor carries the load current plus the Zener current. It must be small enough to keep the Zener conducting at the worst case (lowest input, highest load) and the Zener must survive the other worst case (highest input, lowest load).

R ≤ (VIN(min) − VZ(high)) ÷ (IL(max) + IZ(min))
VIN(min)
lowest supply voltage
VZ(high)
highest Zener voltage, VZ × (1 + tolerance)
IL(max)
highest load current
IZ(min)
smallest Zener current you accept
IZ(max) = (VIN(max) − VZ(low)) ÷ R − IL(min)     PZ(VZ) = VZ × ((VIN(max) − VZ) ÷ R − IL(min))     PR = (VIN(max) − VZ(low))² ÷ R
VZ(low)
lowest Zener voltage, VZ × (1 − tolerance)
IL(min)
lightest load (0 if it can be unplugged)
PZ(VZ)
Zener power for a part whose voltage is VZ; the worst case is its highest value for VZ within tolerance

The output moves with the Zener current through its dynamic resistance:

ΔVOUT ≈ ZZ × (IZ(max) − IZ(min))

Zener diode calculation examples

Example 1: 5.1 V from a 10 to 14 V supply, 0 to 20 mA load

A 1N4733A (5.1 V ±5 %, IZT 49 mA, IZM 178 mA). With 5 mA minimum Zener current, R ≤ (10 − 5.355) ÷ 25 mA = 186 Ω, so 180 Ω from E24. At 10 V and full load the Zener still gets 5.81 mA. At 14 V with the load removed it takes up to 50.9 mA and dissipates up to 257 mW, while the resistor dissipates 466 mW: use a 1 W resistor. With ZZT = 7 Ω the output moves about 315 mV across the range.

Example 2: a 2.5 V bias rail from 12 V

TI’s example: a 2.5 V Zener at 5 mA with no load needs (12 − 2.5) ÷ 5 mA = 1.9 kΩ and burns 47.5 mW in the resistor. A shunt voltage reference that regulates at 75 µA allows 126 kΩ and 716 µW, with a tighter voltage.

Example 3: checking 160 Ω with a 12 V Zener on a 15 to 18 V supply

A 1N4742A (12 V ±5 %, IZM 76 mA) feeding a 0 to 10 mA load. At 15 V and full load the Zener current is 5 mA; at 18 V with no load it is 41.3 mA (470 mW), inside the IZM limit. The resistor dissipates 272 mW. The margin at the low end is thin, because only 15 − 12.6 = 2.4 V is left across the resistor when the Zener is at its high tolerance.

Zener series resistor table for a 12 V supply

What the Zener diode resistor calculator gives for 12 V ±10 % (10.8 to 13.2 V), ±5 % Zeners, 5 mA minimum Zener current and a load that can drop to zero. E24 resistor (rounded down), worst-case Zener power and resistor power.

VZLoad 5 mALoad 10 mALoad 20 mALoad 50 mA
3.3 V680 Ω: PZ 49.6 mW, PR 149 mW470 Ω: PZ 71.8 mW, PR 216 mW270 Ω: PZ 125 mW, PR 375 mW130 Ω: PZ 259 mW, PR 779 mW
5.1 V510 Ω: PZ 82.4 mW, PR 137 mW360 Ω: PZ 117 mW, PR 194 mW200 Ω: PZ 210 mW, PR 349 mW91 Ω: PZ 462 mW, PR 767 mW
6.2 V390 Ω: PZ 112 mW, PR 137 mW270 Ω: PZ 161 mW, PR 198 mW160 Ω: PZ 272 mW, PR 334 mW75 Ω: PZ 581 mW, PR 712 mW
9.1 V120 Ω: PZ 328 mW, PR 173 mW82 Ω: PZ 480 mW, PR 253 mW47 Ω: PZ 838 mW, PR 441 mW22 Ω: PZ 1.79 W, PR 943 mW

1N47xxA Zener datasheet values

From the Vishay 1N4728A to 1N4761A datasheet (Rev. 2.7). The last column shows that the IZM limits correspond to about 0.91 W, below the 1.3 W headline rating.

PartVZIZTIZKZZT (typ)IZMIZM × VZ
1N4728A3.3 V76 mA1 mA10 Ω276 mA911 mW
1N4732A4.7 V53 mA1 mA8 Ω193 mA907 mW
1N4733A5.1 V49 mA1 mA7 Ω178 mA908 mW
1N4735A6.2 V41 mA1 mA2 Ω146 mA905 mW
1N4739A9.1 V28 mA500 µA5 Ω100 mA910 mW
1N4742A12 V21 mA250 µA9 Ω76 mA912 mW
1N4744A15 V17 mA250 µA14 Ω61 mA915 mW

Where a Zener regulator stops being a good idea

A Zener shunt regulator wastes the full (IL(max) + IZ(min)) current all the time, so it suits loads of a few tens of milliamps at most. Its voltage also moves with current (through ZZ), with temperature and within its ±5 % tolerance. For more current, let the Zener set the base of an emitter-follower transistor, or use an LDO; for an accurate reference at low current, use a shunt reference such as the TL431 or LM4040. Pick the series resistor’s wattage and voltage rating with margin, since it dissipates the most when the input is highest.

Glossary

Zener voltage (VZ)
The reverse breakdown voltage, specified at the test current IZT.
Test current (IZT)
The current at which VZ and the dynamic resistance ZZT are specified.
Knee current (IZK)
A low current near the bend of the breakdown curve, where the much higher knee impedance ZZK is specified.
Dynamic resistance (ZZ)
The slope of the Zener curve, ΔVZ ÷ ΔIZ, at a stated current.
IZM
The maximum Zener (regulator) current the datasheet allows.
Shunt regulator
A regulator that holds the output by diverting surplus current to ground, here through the Zener.
Dropout
The load current or input voltage at which the Zener current reaches zero and regulation stops.

Related guides

Frequently asked questions

How do you calculate the resistor for a Zener diode?

R = (VIN(min) − VZ) ÷ (IL(max) + IZ(min)), then round down to a standard value (the Zener calculator above picks it for you). For a 5.1 V Zener (±5 %, so up to 5.355 V) from 10 V with a 20 mA load and 5 mA minimum Zener current, R = 4.645 ÷ 25 mA = 186 Ω, so 180 Ω.

What minimum Zener current should I design for?

Stay well above the knee current IZK where the datasheet specifies the knee impedance (1 mA for a 1N4733A) and remember VZ is specified at IZT (49 mA for that part). A few milliamps is a common floor for small loads; TI notes that ordinary Zeners need as much as 5 mA to reach their rated voltage.

How do you calculate Zener diode power dissipation in a regulator?

PZ = VZ × IZ, taken at the worst case: the highest input with the lightest load, when the Zener takes the largest share of the resistor current. In example 1 the power peaks at 257 mW (48 mA with VZ at 5.355 V, the top of its tolerance); the resistor meanwhile dissipates up to 466 mW.

Why does my Zener regulator output drop when the load is connected?

The resistor carries the load current and the Zener current together. Once the load takes all of it, the Zener stops conducting and the output just follows the resistor divider. In example 1 that happens above 25.8 mA of load at a 10 V input; the Zener diode regulator calculator lists it as the load current at dropout.

How much does the output voltage change across the range?

About ZZ × ΔIZ. The 1N4733A has a typical dynamic resistance of 7 Ω at IZT, and in example 1 the Zener current swings by 45.1 mA, so the output moves about 315 mV on top of the ±5 % tolerance (more near the knee, where the slope is far higher).

When should I use a voltage reference or LDO instead of a Zener?

When the load current is large or varies widely, the Zener must absorb the whole range and wastes power; a linear regulator does not. For a low-current reference, a shunt reference such as the LM4040 regulates at tens of microamps: TI’s example runs one at 75 µA from 12 V through 126 kΩ, dissipating 716 µW in the resistor against 47.5 mW for a Zener at 5 mA.

Is the Zener power rating the power I can use?

Not on a typical PCB. Vishay rates the 1N47xxA series at 1.3 W only with the leads held at ambient 4 mm from the body (test condition tp = 10 ms), and its IZM column (178 mA for the 5.1 V part) works out to about 908 mW. Check the derating curve and keep the worst case comfortably below it.

How do you calculate Zener diode current?

The Zener diode current calculation subtracts the load current from the series resistor current: IZ = (VIN − VZ) ÷ R − IL. In example 1, with 180 Ω, that is 5.81 mA at 10 V and full load and up to 50.9 mA at 14 V with no load. The Check a resistor mode works as a Zener current calculator: enter your resistor and it reports both extremes.

How does a Zener diode work as a voltage regulator?

It works as a shunt regulator: reverse breakdown holds the output near VZ while the series resistor drops the rest of the supply and the surplus current is diverted to ground through the Zener. It suits loads of a few tens of milliamps at most. This shunt regulator calculator checks both ends of the range: regulation at the lowest input with the heaviest load, and Zener power at the highest input with the lightest load.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.