NewAI Part GeneratorFree to get started
FREE TOOL

Johnson noise calculator (resistor thermal noise)

Every resistor is a noise source, and this Johnson noise calculator gives its voltage and current noise density, rms noise over your bandwidth and the available noise power in dBm. Pick a filter type to convert its −3 dB frequency into noise bandwidth, or find the resistance that matches an op amp’s noise.

Solve for
Examples
Ω
°C

290 K (16.85 °C) is the reference for −174 dBm/Hz.

Hz

Pick a filter to convert its −3 dB frequency into noise bandwidth.

Voltage noise density

4.058 nV/√Hz

RMS noise voltage
405.8 nV in 10 kHz
Peak-to-peak (6.6 × rms)
2.678 µV
Current noise density
4.058 pA/√Hz
RMS noise current
405.8 pA
Available noise power kTB
-133.85 dBm
Noise power density kT
-173.85 dBm/Hz
Into a matched load (vn ÷ 2)
202.9 nV
Absolute temperature
298.15 K

Thermal noise only, which every resistor has. Current through a real resistor adds excess (1/f) noise on top, notably in carbon-composition parts and least in wirewound (TI SLVA043B).

Noise density versus resistance at 25.0 °C
1n10n100n1µ100f1p10p100p1101001k10k100k1M10M100MResistance (Ω)Voltage noise (V/√Hz)Current noise (A/√Hz)R 1 kΩ
Voltage noise densityCurrent noise density

Noise of common resistors at 25 °C over 10 kHz

ResistanceVoltage densityRMS voltageCurrent density
10 Ω405.8 pV/√Hz40.58 nV40.58 pA/√Hz
50 Ω907.3 pV/√Hz90.73 nV18.15 pA/√Hz
100 Ω1.283 nV/√Hz128.3 nV12.83 pA/√Hz
1 kΩ4.058 nV/√Hz405.8 nV4.058 pA/√Hz
10 kΩ12.83 nV/√Hz1.283 µV1.283 pA/√Hz
100 kΩ40.58 nV/√Hz4.058 µV405.8 fA/√Hz
1 MΩ128.3 nV/√Hz12.83 µV128.3 fA/√Hz
10 MΩ405.8 nV/√Hz40.58 µV40.58 fA/√Hz

How do you calculate the thermal noise of a resistor?

Use vn = √(4kTRB), with k = 1.380649 × 10⁻²³ J/K, T in kelvin, R in ohms and B the noise bandwidth in hertz. A 1 kΩ resistor at 25 °C (298.15 K) has a noise density of 4.06 nV/√Hz, so over 10 kHz it produces 406 nV rms. Noise grows with the square root of resistance and of bandwidth: four times the resistance doubles it.

Johnson noise formula for voltage, current and power

Johnson measured it and Nyquist derived it in 1928: a resistor behaves like a noiseless resistor in series with a white noise voltage source, or in parallel with a white noise current source.

en = √(4kTR)     in = √(4kT ÷ R)
en
voltage noise density in V/√Hz
in
current noise density in A/√Hz
k
Boltzmann constant, 1.380649 × 10⁻²³ J/K (exact)
T
absolute temperature in K (°C + 273.15)
R
resistance in Ω

Over a noise bandwidth B, the Johnson noise equation gives the rms voltage and the power the resistor can deliver into a matched load:

vn = √(4kTRB)     P = kTB

A real filter is not a brick wall, so its noise bandwidth is wider than its −3 dB frequency fc. For an n-th order Butterworth low-pass, B = fc × (π/2n) ÷ sin(π/2n): 1.571 × fc for a single RC pole, 1.111 for 2nd order, 1.047 for 3rd and 1.026 for 4th, matching TI SLVA043B. The formula is the low-frequency limit of Nyquist’s result and holds while hf ≪ kT, which at room temperature is true up to roughly 100 GHz.

How to calculate Johnson noise: worked examples

Example 1: a 10 kΩ resistor across the audio band

At 25 °C, en = √(4 × 1.380649 × 10⁻²³ × 298.15 × 10,000) = 12.8 nV/√Hz. Over 20 kHz, vn = 12.8 nV/√Hz × √20,000 = 1.81 µV rms, about 12 µV peak-to-peak. A source impedance of 10 kΩ in front of a 4 nV/√Hz op amp is dominated by its own noise, not the amplifier’s.

Example 2: the noise floor of a 50 Ω system over 1 MHz

At 290 K, kT is −173.98 dBm/Hz. Over 1 MHz add 60 dB: −114.0 dBm. The open-circuit noise voltage of the 50 Ω source is 895 nV rms, and half of that, 447 nV, appears across a matched 50 Ω load. Any receiver adds its noise figure on top of this floor.

Example 3: a 1 MΩ bias resistor behind a 100 Hz RC filter

The noise density is 128 nV/√Hz (current density 128 fA/√Hz). A single-pole filter at 100 Hz has a noise bandwidth of 1.571 × 100 Hz = 157.1 Hz, so vn = 128 nV/√Hz × √157.1 = 1.61 µV rms. Using the 100 Hz corner as if it were a brick wall would understate it by 20 %.

Resistor noise voltage and current for common values at 25 °C

Density, current noise and rms noise over the audio band (20 kHz) and over 1 MHz, all as noise bandwidths.

ResistanceVoltage densityCurrent densityRMS in 20 kHzRMS in 1 MHz
10 Ω405.8 pV/√Hz40.58 pA/√Hz57.39 nV405.8 nV
50 Ω907.3 pV/√Hz18.15 pA/√Hz128.3 nV907.3 nV
100 Ω1.283 nV/√Hz12.83 pA/√Hz181.5 nV1.283 µV
1 kΩ4.058 nV/√Hz4.058 pA/√Hz573.9 nV4.058 µV
10 kΩ12.83 nV/√Hz1.283 pA/√Hz1.815 µV12.83 µV
100 kΩ40.58 nV/√Hz405.8 fA/√Hz5.739 µV40.58 µV
1 MΩ128.3 nV/√Hz128.3 fA/√Hz18.15 µV128.3 µV
10 MΩ405.8 nV/√Hz40.58 fA/√Hz57.39 µV405.8 µV

Noise versus temperature

Noise power scales with absolute temperature, so noise voltage scales with its square root. Cooling from 25 °C to liquid nitrogen cuts the voltage noise roughly in half.

TemperatureKelvin1 kΩ density50 Ω densitykT
4.2 K (liquid helium)4.2 K481.6 pV/√Hz107.7 pV/√Hz−192.37 dBm/Hz
77 K (liquid nitrogen)77 K2.062 nV/√Hz461.1 pV/√Hz−179.73 dBm/Hz
−55 °C218.15 K3.471 nV/√Hz776.1 pV/√Hz−175.21 dBm/Hz
−40 °C233.15 K3.588 nV/√Hz802.4 pV/√Hz−174.92 dBm/Hz
0 °C273.15 K3.884 nV/√Hz868.5 pV/√Hz−174.24 dBm/Hz
16.85 °C (290 K)290 K4.002 nV/√Hz894.9 pV/√Hz−173.98 dBm/Hz
25 °C298.15 K4.058 nV/√Hz907.3 pV/√Hz−173.85 dBm/Hz
85 °C358.15 K4.447 nV/√Hz994.5 pV/√Hz−173.06 dBm/Hz
125 °C398.15 K4.689 nV/√Hz1.049 nV/√Hz−172.60 dBm/Hz

Using the result in a real design

Use this resistor noise calculator to compare a source resistance with the amplifier it feeds. A 4 nV/√Hz op amp has the same voltage noise as a 972 Ω resistor at 25 °C; source and feedback resistances well above that dominate the noise, and lowering them is the cheapest improvement, at the cost of more current. High resistances also turn the amplifier’s current noise into voltage noise, so a low-noise design keeps impedances moderate. Thermal noise is the floor, not the whole story: resistors carrying DC current add excess (1/f) noise, and parasitic capacitance across a large resistor limits the bandwidth, which is why the total noise of R in parallel with C never exceeds √(kT/C). Noise from separate sources adds as a root sum of squares, so the largest contributor sets the total.

Glossary

Johnson-Nyquist noise
The thermal noise of any resistance, caused by the random motion of charge carriers. Also called thermal or resistor noise.
Noise density
Noise per root hertz (nV/√Hz or pA/√Hz). Multiply by √bandwidth for an rms value.
Equivalent noise bandwidth (ENBW)
The width of a brick-wall filter that passes the same noise power as a real filter; 1.571 × fc for one RC pole.
kTB
Noise power available from a resistor into a matched load: −174 dBm/Hz at 290 K, plus 10·log10(B).
White noise
Noise with the same density at every frequency. Thermal noise is white up to far beyond electronic frequencies.
Excess (1/f) noise
Extra noise in real resistors that rises at low frequency and grows with the DC current through them.

Related guides

Frequently asked questions

What is Johnson-Nyquist noise?

The noise every resistance produces from the random motion of its charge carriers, also called thermal or resistor noise. It is white up to far beyond electronic frequencies and depends only on resistance, temperature and bandwidth.

What is the thermal noise formula?

vn = √(4kTRB) for the rms voltage over a noise bandwidth B, en = √(4kTR) for the density, and P = kTB for the power into a matched load. k is the Boltzmann constant, 1.380649 × 10⁻²³ J/K, and T is in kelvin.

What is the thermal noise of a 1 kΩ resistor?

4.06 nV/√Hz at 25 °C, usually rounded to 4 nV/√Hz. Over a 10 kHz noise bandwidth that is 406 nV rms, and over 20 kHz it is 574 nV rms.

Why is thermal noise −174 dBm/Hz?

A resistor at temperature T can deliver kT watts per hertz into a matched load, whatever its resistance. At the 290 K reference temperature kT = 4.004 × 10⁻²¹ W/Hz, which is −173.98 dBm/Hz. Add 10·log10(B) for a bandwidth B: 1 MHz adds 60 dB.

Does resistor noise depend on the current or the resistor type?

Thermal noise does not: it depends only on resistance, temperature and bandwidth. Current through a resistor adds excess (1/f) noise on top, which TI SLVA043B notes is found in carbon-composition resistors, is least in wirewound, and is negligible when the current is small.

How do I turn a noise density into an rms voltage?

Multiply by the square root of the noise bandwidth. A real filter lets some noise through above its −3 dB point, so use its equivalent noise bandwidth: 1.571 × fc for a single RC pole and 1.111 × fc for a 2nd-order Butterworth. The resistor thermal noise calculator above does this when you pick the filter type.

How do noise sources add?

Uncorrelated noise adds as the root sum of squares, not linearly. Two resistors in series give the noise of their sum, √(4kT(R1 + R2)B), and two in parallel give the noise of the parallel combination.

How do I convert rms noise to peak-to-peak?

Thermal noise is Gaussian, so there is no hard peak. ADI MT-048 uses 6.6 × rms, which is exceeded 0.1 % of the time; TI SLVA043B uses 6 × rms for 99.7 %. A 1 kΩ resistor over 10 kHz at 25 °C is about 2.68 µV peak-to-peak.

What is kT/C noise?

When a capacitor C sits across a resistor, the noise bandwidth is 1/(4RC), and the total noise works out to √(kT/C) whatever R is. For 1 pF at 25 °C that is 64.2 µV rms; it sets the noise floor of sampling capacitors in ADCs.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.