NewAI Part GeneratorFree to get started
FREE TOOL

Common-emitter calculator (BJT biasing)

Work out the Q-point of a voltage-divider biased BJT stage with this common-emitter calculator: base, emitter and collector voltages, currents and VCE, with a saturation check and how much the bias moves across the transistor’s β spread. It also gives the small-signal gain and input impedance with or without an emitter bypass capacitor.

Examples
V
Ω
Ω
Ω
Ω

Use the minimum and typical datasheet hFE to see the spread.

V

About 0.6 to 0.7 V for a silicon BJT at milliamp currents.

Emitter bypass capacitor
Ω

Optional: AC load on the collector through a coupling capacitor.

Collector current IC

1.229 mA

Operating region
Active (linear)
Collector-emitter voltage VCE
6.13 V
Base voltage VB
4.776 V
Emitter voltage VE
4.076 V
Collector voltage VC
10.21 V
Base current IB
6.145 µA
Emitter current IE
1.235 mA
Thevenin base voltage VTH
4.796 V RTH = 3.2 kΩ
Transistor dissipation
7.539 mW
IC at β = 100 and 400
1.22 mA to 1.24 mA 1.5% spread
Divider current (through R2) ÷ IB
165 ×
Stability factor S (ΔIC/ΔICBO)
1.96 1 is ideal, 201 is unstabilized
Dynamic emitter resistance r'e
20.8 Ω VT / IE at 25 °C
Voltage gain Av
-1.174 1.4 dB, inverting
Input impedance Zin
3.182 kΩ Zin(base) = 667 kΩ
Output impedance Zout
3.9 kΩ ≈ RC

RTH/(β+1) is 0.5% of RE, so the Q-point barely depends on β (1.5% spread over a 4:1 range of β).

DC load line and Q-point
0500µ1m1.5m2m02468101214VCE (V)IC (A)IC 1.23 mAVCE 6.13 V

Q-point across the β spread

β (hFE)ICVCERegion
501.19 mA6.32 VActive
1001.22 mA6.2 VActive
1501.23 mA6.15 VActive
2001.23 mA6.13 VActive
3001.23 mA6.11 VActive
4001.24 mA6.1 VActive

How do you calculate the Q-point of a BJT voltage divider bias circuit?

Reduce the divider to VTH = VCC·R2/(R1+R2) and RTH = R1∥R2, then IB = (VTH − VBE) ÷ (RTH + (β+1)·RE), IC = β·IB and VCE = VCC − IC·RC − IE·RE. With 15 V, R1 = 10 kΩ, R2 = 4.7 kΩ, RC = 3.9 kΩ, RE = 3.3 kΩ and β = 200, IC = 1.23 mA and VCE = 6.13 V. If VCE comes out below about 0.2 V, the transistor is saturated.

Voltage divider bias formulas and common-emitter gain

R1 and R2 set the base voltage, RE sets the emitter current, and RC turns that current into the collector voltage. The divider is first reduced to its Thevenin equivalent.

VTH = VCC × R2 ÷ (R1 + R2)     RTH = R1 × R2 ÷ (R1 + R2)
VTH, RTH
Thevenin voltage and resistance of the base divider
β
DC current gain hFE
VBE
base-emitter voltage, about 0.6 to 0.7 V
IB = (VTH − VBE) ÷ (RTH + (β + 1) × RE)     IC = β × IB     IE = (β + 1) × IB
VE = IE × RE     VB = VE + VBE     VC = VCC − IC × RC     VCE = VC − VE

If VCE comes out below VCE(sat) (taken as 0.2 V), the transistor is saturated and the Q-point calculator solves the base and collector loops again with VCE fixed at 0.2 V. Small-signal figures at mid-band frequencies:

Av = −rC ÷ (r'e + rE)     Zin = R1 ∥ R2 ∥ (β + 1)(r'e + rE)     Zout ≈ RC
r'e
dynamic emitter resistance, VT ÷ IE (VT = kT/q = 25.7 mV at 25 °C)
rC
RC in parallel with the load
rE
emitter resistance left unbypassed (0 when fully bypassed)

The stability factor says how far IC moves per unit of collector-base leakage. It follows from the base loop with IC = β·IB + (β + 1)·ICBO, and the IIT (ISM) class notes in the sources derive the same form for this bias network: S = 1 is ideal and S = β + 1 means no stabilization at all.

S = ΔIC ÷ ΔICBO = (β + 1) ÷ (1 + β × RE ÷ (RTH + RE))

Common-emitter amplifier worked examples

Example 1: 15 V stage with β = 200

VTH = 15 × 4.7k ÷ 14.7k = 4.8 V and RTH = 3.2 kΩ. IB = (4.8 V − 0.7) ÷ (3.2 kΩ + 201 × 3.3 kΩ = 666 kΩ) = 6.15 µA, so IC = 1.23 mA, VE = 4.08 V, VC = 10.2 V and VCE = 6.13 V. The load line runs from 2.08 mA at VCE = 0 to 15 V at IC = 0. With β = 100 instead, IC is 1.22 mA. The stability factor is S = 1.96, against 10.2 for the same stage with a divider ten times weaker.

Example 2: 12 V stage with a 100 Ω swamping resistor

R1 = 56 kΩ, R2 = 10 kΩ, RC = 4.7 kΩ, RE = 1 kΩ (900 Ω bypassed, 100 Ω not), β = 150, VBE = 0.65 V and a 10 kΩ load. The Q-point is IC = 1.1 mA, VCE = 5.73 V. r'e = 23.2 Ω, so Av = −(4.7k ∥ 10k) ÷ (23.2 Ω + 100 Ω) = -25.9 and Zin = 5.83 kΩ. Bypassing all of RE would give -138, set mostly by r'e and therefore by temperature.

Example 3: an RC that is too large

Change RC in example 1 to 10 kΩ. The linear solution would put VC at 15 − 1.23 mA × 10 kΩ = 2.71 V, below VE (4.08 V), which is impossible. The transistor saturates: solving with VCE = 0.2 V gives IC = 1.09 mA, and the stage no longer amplifies. Either lower RC or lower the emitter current.

Collector current across the β spread

A 2N3904 is specified from hFE 100 to 300 at 10 mA, so the bias has to tolerate a wide range. The stiff divider of example 1 (R1 = 10 kΩ, R2 = 4.7 kΩ) against a divider ten times weaker (100 kΩ, 47 kΩ) with the same ratio:

βIC, 10k/4.7k dividerVCEIC, 100k/47k dividerVCE
501.19 mA6.32 V1.02 mA7.57 V
1001.22 mA6.2 V1.12 mA6.89 V
1501.23 mA6.15 V1.16 mA6.63 V
2001.23 mA6.13 V1.18 mA6.5 V
3001.23 mA6.11 V1.2 mA6.36 V
4001.24 mA6.1 V1.21 mA6.29 V

Gain against emitter bypassing

Example 1 circuit, no load. The DC Q-point is the same in every row; only the AC emitter resistance changes.

Emitter bypassGain AvGain (dB)Zin
None (rE = RE = 3.3 kΩ)-1.171.4 dB3.18 kΩ
1 kΩ unbypassed-3.8211.6 dB3.15 kΩ
200 Ω unbypassed-17.6624.9 dB2.98 kΩ
Fully bypassed (rE = 0)-187.5045.5 dB1.81 kΩ

Common-emitter amplifier design that works on the bench

Size the divider so RTH/(β+1) is a small fraction of RE, using the lowest hFE on the datasheet; the β sweep in this BJT biasing calculator shows directly whether the Q-point holds. Drop a volt or more across RE so the −2 mV/°C drift of VBE is a small fraction of it, and leave VCE several volts above saturation for the signal to swing. The model ignores the transistor’s own output resistance (the Early effect, on the order of 100 kΩ, which slightly lowers gain and Zout), leakage, and frequency effects: coupling and bypass capacitors set the low-frequency corner, and junction capacitances set the high one. Use 1% resistors in the divider and RE when the gain must be predictable.

Glossary

Q-point
The DC operating point of the transistor: IC and VCE with no signal applied.
Thevenin equivalent
The base divider replaced by one voltage VTH in series with one resistance RTH = R1∥R2.
r'e
Small-signal emitter resistance VT/IE, about 26 Ω at 1 mA.
Swamping resistor
Unbypassed emitter resistance that makes the gain depend on resistors rather than on r′e.
Bypass capacitor
A capacitor across RE that shorts it for AC signals and raises the gain.
DC load line
The line from IC = VCC/(RC+RE) at VCE = 0 to IC = 0 at VCE = VCC; the Q-point lies on it.
Saturation
Both junctions forward biased, VCE near 0.2 V; IC no longer depends on IB.
Cutoff
The base voltage is below VBE, so no collector current flows and VCE = VCC.

Related guides

Frequently asked questions

How do you find the Q-point of a voltage divider bias circuit?

Replace the divider with its Thevenin equivalent (VTH = VCC·R2/(R1+R2), RTH = R1∥R2), then IB = (VTH − VBE)/(RTH + (β+1)RE), IC = βIB and VCE = VCC − IC·RC − IE·RE. For VCC = 15 V, R1 = 10 kΩ, R2 = 4.7 kΩ, RC = 3.9 kΩ, RE = 3.3 kΩ and β = 200 that gives IC = 1.23 mA and VCE = 6.13 V.

Why is voltage divider bias stable against changes in β?

Because RE appears multiplied by (β+1) in the base loop, so as long as RTH/(β+1) is small next to RE the collector current is set by (VTH − VBE)/RE. In the example, halving β from 200 to 100 changes IC from 1.23 mA to 1.22 mA, under 1%.

What is r'e and how do you calculate it?

r'e is the small-signal resistance of the base-emitter junction, VT/IE. At 25 °C, VT = kT/q = 25.69 mV, so r'e = 25.7 Ω at 1 mA. Textbooks often round VT to 26 mV.

What is the common-emitter gain formula?

The voltage gain is Av = −rC/(r'e + rE), where rC is RC in parallel with the load and rE is the emitter resistance not bypassed by a capacitor. With all of RE unbypassed the gain is close to −RC/RE; the example stage with 100 Ω unbypassed and a 10 kΩ load has Av = -25.9.

How can I tell if the transistor is saturated?

Solve the stage as if it were linear. If VCE comes out below about 0.2 V (or negative), it is saturated: IC is then limited by VCC/(RC + RE) and no longer depends on β. The transistor biasing calculator detects this and solves the saturated circuit instead.

What does the emitter bypass capacitor do?

It shorts RE for AC signals so it no longer reduces the gain, while keeping the DC bias stable. Fully bypassed, the gain becomes −rC/r'e (-138 in example 2, against -25.9 with 100 Ω left unbypassed), but it then varies with IE and temperature and large signals distort.

How much does temperature shift the bias point?

VBE falls about 2 mV per °C. In the 15 V example, VE is 4.08 V, so a 25 °C rise adds about 50 mV across RE and raises IC by roughly 1.2%. The more voltage you drop across RE, the smaller this effect.

How do you bias a BJT?

With voltage divider bias, R1 and R2 set the base voltage, RE sets the emitter current, and RC turns that current into the collector voltage. Size the divider so RTH/(β+1) is a small fraction of RE at the lowest hFE on the datasheet, drop a volt or more across RE, and leave VCE several volts above saturation for the signal to swing.

What is DC biasing of a BJT?

DC biasing sets the transistor’s operating point, the Q-point: IC and VCE with no signal applied. The Q-point lies on the DC load line, which runs from IC = VCC/(RC+RE) at VCE = 0 to IC = 0 at VCE = VCC.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.