NewAI Part GeneratorFree to get started
FREE TOOL

Resistor combination calculator

To make an odd value, this resistor combination calculator finds the two standard resistors that land closest in series or in parallel, from the E12, E24, E48 or E96 series. Pairs are ranked by error and compared with the nearest single value, with the worst-case and statistical tolerance of the result.

Examples
Ω

Type 12.3k, 4k99, 680 and so on.

Resistor series
Connection

For the spread of the result. 1 % chip resistors come in both E24 and E96 values.

Best parallel pair (E24)

13 kΩ ∥ 240 kΩ

12.332 kΩ, −0.105 %

Combined value
12.332 kΩ
Error
−0.105 %
Nearest single E24 value
12 kΩ −2.79 %
Worst case with ±1 % parts
±1.1 % single: ±3.77 %
Spread if part errors are independent
±0.95 % 0.95 × one part’s

Best series or parallel pairs from E24 (spread for independent ±1 % parts)

R1R2ConnectionResultErrorSpread
13 kΩ240 kΩParallel12.332 kΩ−0.105 %±0.95 %
360 Ω12 kΩSeries12.36 kΩ+0.122 %±0.97 %
330 Ω12 kΩSeries12.33 kΩ−0.122 %±0.97 %
18 kΩ39 kΩParallel12.3158 kΩ−0.237 %±0.75 %
1.3 kΩ11 kΩSeries12.3 kΩ−0.365 %±0.9 %
390 Ω12 kΩSeries12.39 kΩ+0.365 %±0.97 %
300 Ω12 kΩSeries12.3 kΩ−0.365 %±0.98 %
6.2 kΩ6.2 kΩSeries12.4 kΩ+0.446 %±0.71 %
5.6 kΩ6.8 kΩSeries12.4 kΩ+0.446 %±0.71 %
3.3 kΩ9.1 kΩSeries12.4 kΩ+0.446 %±0.78 %

Can you combine resistors to make a value you cannot buy?

Yes: combine them in series (R1 + R2) or in parallel (R1 × R2 ÷ (R1 + R2)) and pick the pair that lands closest. For 12.345 kΩ from E24, 13 kΩ ∥ 240 kΩ gives 12.332 kΩ, −0.105 % off, where the nearest single resistor (12 kΩ) is −2.79 % off. With ±1 % parts the pair can be at most ±1.1 % from the target.

Resistor combination formulas

The calculator ranks by error the pairs of standard values that land within 5 % of the target. Series parts go down to 1/1000 of the target and parallel parts up to 1000 times it, since a more extreme trim moves the result by less than the tolerance of a ±0.1 % part. For a target from 1 Ω to 10 MΩ both parts also stay in that range.

Series: R = R1 + R2     Parallel: R = R1 × R2 ÷ (R1 + R2)
R1, R2
the two standard resistors, in Ω
R
the combined value

The nominal error against the target, and the worst case once each part may be off by ±t:

e = (R − Rtarget) ÷ Rtarget     worst case = (1 + e)(1 ± t) − 1
e
nominal error of the pair, as a fraction
t
part tolerance, as a fraction (0.01 for ±1 %)

The pair is never worse than ±t, because scaling both parts by (1 + t) scales the series sum and the parallel value by exactly (1 + t). If the two parts’ errors are independent, the root-sum-of-squares spread is smaller:

spread = t × √(R1² + R2²) ÷ (R1 + R2)

That is 0.707 t for two equal resistors and close to t when one resistor is much larger than the other, in either connection. Among pairs with the same error, the calculator lists the more evenly matched one first.

Worked examples

Example 1: 12.345 kΩ from E24

The nearest single E24 value, 12 kΩ, is −2.79 % off. The best pair is a parallel one, 13 kΩ ∥ 240 kΩ: 13 × 240 ÷ 253 kΩ = 12.332 kΩ, −0.105 %. The best series pair, 360 Ω + 12 kΩ = 12.36 kΩ, is nearly as close (+0.122 %). With ±1 % parts the parallel pair stays within ±1.1 % of 12.345 kΩ.

Example 2: 2.5 kΩ from E12

E12 jumps from 2.2 kΩ to 2.7 kΩ, so the nearest single value is 2.7 kΩ, which is +8 % off. In series, 1 kΩ + 1.5 kΩ is exactly 2.5 kΩ. With ±5 % parts the pair stays within ±5 %, against ±13.4 % for the single 2.7 kΩ.

Example 3: 1.234 kΩ from E96 with 0.1 % parts

The nearest E96 value, 1.24 kΩ, is +0.486 % off, several times the 0.1 % tolerance. 536 Ω + 698 Ω makes 1.234 kΩ exactly. The two parts are close in value, so if their errors are independent the result spreads only about ±0.0713 % (0.713 of one part’s ±0.1 %).

E96 values from two E24 resistors

When only E24 parts are stocked, these resistor combinations land closest to some common E96 values. Errors are nominal, before part tolerance.

Target (E96)Best E24 pairResultErrorNearest single E24
1.05 kΩ430 Ω + 620 Ω1.05 kΩexact1.1 kΩ (+4.76 %)
1.13 kΩ510 Ω + 620 Ω1.13 kΩexact1.1 kΩ (−2.65 %)
1.43 kΩ680 Ω + 750 Ω1.43 kΩexact1.5 kΩ (+4.9 %)
2.49 kΩ91 Ω + 2.4 kΩ2.491 kΩ+0.0402 %2.4 kΩ (−3.61 %)
3.48 kΩ180 Ω + 3.3 kΩ3.48 kΩexact3.6 kΩ (+3.45 %)
4.99 kΩ5.1 kΩ ∥ 240 kΩ4.99388 kΩ+0.0778 %5.1 kΩ (+2.2 %)
6.04 kΩ6.2 kΩ ∥ 240 kΩ6.04387 kΩ+0.064 %6.2 kΩ (+2.65 %)
8.06 kΩ560 Ω + 7.5 kΩ8.06 kΩexact8.2 kΩ (+1.74 %)

Round values from two E12 resistors

Values that fall between E12 steps, made from the coarsest common series.

TargetBest E12 pairResultErrorNearest single E12
2.5 kΩ1 kΩ + 1.5 kΩ2.5 kΩexact2.7 kΩ (+8 %)
4 kΩ1.8 kΩ + 2.2 kΩ4 kΩexact3.9 kΩ (−2.5 %)
5 kΩ10 kΩ ∥ 10 kΩ5 kΩexact4.7 kΩ (−6 %)
6 kΩ12 kΩ ∥ 12 kΩ6 kΩexact5.6 kΩ (−6.67 %)
25 kΩ10 kΩ + 15 kΩ25 kΩexact27 kΩ (+8 %)
40 kΩ18 kΩ + 22 kΩ40 kΩexact39 kΩ (−2.5 %)
50 kΩ100 kΩ ∥ 100 kΩ50 kΩexact47 kΩ (−6 %)
60 kΩ120 kΩ ∥ 120 kΩ60 kΩexact56 kΩ (−6.67 %)

Using a pair on a real board

Power divides with the values: in series each resistor dissipates in proportion to its resistance, in parallel in inverse proportion, so check each part’s rating rather than the total. A pair costs an extra placement and board area, so first check whether a single E96 or E192 value is close enough; 1 % chip resistors are commonly sold in both E24 and E96 values. Parts from the same reel can err in the same direction, which pushes the result toward the worst case rather than the statistical spread. For very high values, board leakage in parallel with the pair matters more than the last fraction of a percent; for very low values, solder joints and trace resistance add to a series pair.

Glossary

E-series
The IEC 60063 preferred values: E12 has 12 values per decade, E24 has 24, E96 has 96.
Nominal error
How far the pair’s marked value is from the target, before part tolerance.
Tolerance
The most a part may differ from its marked value, for example ±1 %.
Worst case
Nominal error plus every part at its tolerance limit in the same direction.
Statistical spread
The likely spread when part errors are independent: the root-sum-of-squares of each part’s weighted error.
Parallel (∥)
R1 ∥ R2 = R1 × R2 ÷ (R1 + R2), always less than the smaller resistor.

Related guides

Frequently asked questions

How do I make a resistor value that is not standard?

Put two standard resistors in series (their values add) or in parallel (product over sum). For 12.345 kΩ the best E24 pair is 13 kΩ ∥ 240 kΩ = 12.332 kΩ (−0.105 %), against −2.79 % for the nearest single value.

How do I make 5 kΩ from standard resistors?

10 kΩ ∥ 10 kΩ gives exactly 5 kΩ. Two equal resistors in parallel always give half the value, and two in series give double.

Should I combine resistors in series or in parallel?

Whichever lands closer; the calculator tries both. In series a small resistor trims a large one upward, and the larger part dissipates more power. In parallel a large resistor trims a smaller one downward, and the smaller part takes more of the current.

What is the tolerance of two resistors in series or parallel?

No worse than the parts: two ±1 % resistors make a ±1 % result in either connection, because scaling both by 1.01 scales the result by 1.01. If their errors are independent the spread is smaller, down to 0.707 of one part’s for two equal values.

Is it worth using two resistors instead of one?

When the nearest single value misses by more than the tolerance, yes. For 2.5 kΩ with ±5 % parts, the nearest E12 value (2.7 kΩ) can be ±13.4 % off, while 1 kΩ + 1.5 kΩ is within ±5 %. When a 1 % E96 part already exists near the value, one resistor is simpler and cheaper to place.

What is the resistor combination formula?

In series the values add: R = R1 + R2. In parallel it is product over sum: R = R1 × R2 ÷ (R1 + R2), always less than the smaller resistor.

How many values are in the E24 and E96 series?

IEC 60063 defines 24 values per decade for E24 and 96 for E96 (plus E3, E6, E12, E48 and E192). Each step is about 10^(1/n), so E24 values are about 10 % apart and E96 values about 2.4 % apart.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.