NewAI Part GeneratorFree to get started
FREE TOOL

Inductors in series and parallel calculator

Work out the total inductance of inductors in series and parallel, up to six at a time, or of two magnetically coupled windings aiding or opposing, from their coupling coefficient or mutual inductance. You can also find the mutual inductance from two series measurements.

Connection
Examples
H
H

Up to 6 inductors; the next field appears as you fill this one.

H

Total inductance (series)

32 µH

Assumes no magnetic coupling: shielded inductors, or unshielded ones spaced apart or at right angles. If flux from one links another, use the coupled pair tab.

The same current flows through every inductor in series, so each must be rated for the full current. DCR adds too.

Share of the AC voltage across each inductor

InductorValueShare
L110 µH31.3 %
L222 µH68.8 %

How do you calculate inductors in series and parallel?

Uncoupled inductors combine like resistors. In series they add: 10 µH + 22 µH = 32 µH. In parallel the reciprocals add: 10 µH ∥ 22 µH = 6.875 µH. When the fields of two inductors link, the mutual inductance M joins in: L1 + L2 ± 2M in series, plus when the fields aid and minus when they oppose.

Inductors in series and parallel formulas, with mutual inductance

Without magnetic coupling, inductors combine exactly like resistors: the same current through a series string, the same voltage across a parallel group.

Series: L = L1 + L2 + …     Parallel: 1/L = 1/L1 + 1/L2 + …
L
total inductance in H
L1, L2 …
the individual inductances in H

Two coils whose fields link share a mutual inductance M, set by the coupling coefficient k (0 to 1):

M = k × √(L1 × L2)
M
mutual inductance in H
k
coupling coefficient, 0 to 1

In series the mutual term appears twice, once for each coil’s effect on the other. Upper signs are for aiding fields, lower signs for opposing:

Series: L = L1 + L2 ± 2M     Parallel: L = (L1 × L2 − M²) ÷ (L1 + L2 ∓ 2M)

The parallel form comes from writing v = L1 di1/dt ± M di2/dt = ±M di1/dt + L2 di2/dt for the shared voltage and solving for the total di/dt; Evstatiev’s lecture notes (in the sources below) work it through and give the same result, with −2M in the denominator for aiding fields and +2M for opposing. Measuring the two series connections gives M directly, and shorting one winding leaves the leakage inductance:

M = (La − Lo) ÷ 4     L1 + L2 = (La + Lo) ÷ 2     L1(L2 shorted) = L1 (1 − k²)

Worked examples

Example 1: 10 µH, 22 µH and 4.7 µH, shielded

In series the three add to 36.7 µH. In parallel, 1/L = 1/10 + 1/22 + 1/4.7 µH⁻¹, so L = 2.792 µH, below the smallest part. Both assume no coupling, which well-shielded parts come close to.

Example 2: both windings of a Coilcraft MSD1260-472

Each winding is 4.7 µH and the typical coupling is 0.98, so M = 0.98 × 4.7 µH = 4.606 µH. In series aiding the part gives 18.61 µH, close to the datasheet’s “four times the value” (18.8 µH). In parallel aiding it gives 4.653 µH, the datasheet’s “same value”. With one winding shorted the other shows 186.1 nH, against 0.20 µH typical leakage inductance on the datasheet.

Example 3: finding M with an LCR meter

Two coils read 250 mH in series aiding and 150 mH with one reversed. M = (250 − 150) ÷ 4 = 25 mH and L1 + L2 = 200 mH. If coil 1 alone reads 150 mH, coil 2 is 50 mH and k = 25 ÷ √(150 × 50) = 0.289, a loose coupling.

Two equal inductors: effect of coupling

Total inductance as a multiple of one inductor L, for two equal windings at different coupling coefficients. k = 0 is the uncoupled case.

kSeries aidingSeries opposingParallel aidingParallel opposing
02.000 L2.000 L0.500 L0.500 L
0.12.200 L1.800 L0.550 L0.450 L
0.32.600 L1.400 L0.650 L0.350 L
0.53.000 L1.000 L0.750 L0.250 L
0.73.400 L0.600 L0.850 L0.150 L
0.93.800 L0.200 L0.950 L0.050 L
0.983.960 L0.040 L0.990 L0.010 L
14.000 L0.000 L1.000 L0.000 L

Two inductors in parallel: common values

L1 × L2 ÷ (L1 + L2), with no coupling. Two equal inductors in parallel give half the value.

L1 \ L21 µH2.2 µH4.7 µH10 µH22 µH47 µH100 µH
1 µH500 nH687.5 nH824.6 nH909.1 nH956.5 nH979.2 nH990.1 nH
2.2 µH687.5 nH1.1 µH1.499 µH1.803 µH2 µH2.102 µH2.153 µH
4.7 µH824.6 nH1.499 µH2.35 µH3.197 µH3.873 µH4.273 µH4.489 µH
10 µH909.1 nH1.803 µH3.197 µH5 µH6.875 µH8.246 µH9.091 µH
22 µH956.5 nH2 µH3.873 µH6.875 µH11 µH14.99 µH18.03 µH
47 µH979.2 nH2.102 µH4.273 µH8.246 µH14.99 µH23.5 µH31.97 µH
100 µH990.1 nH2.153 µH4.489 µH9.091 µH18.03 µH31.97 µH50 µH

What changes on a real board

Unshielded inductors placed side by side couple through their stray fields, so the uncoupled formulas only hold for shielded parts, for parts spaced well apart, or for coils at right angles to each other. Every inductor in series carries the full current, so each needs a saturation and RMS current rating above it, and the DCRs add. Parallel inductors share AC current by inductance but DC current by DCR, so two nominally equal parts (often ±20 % in inductance) rarely split evenly; leave margin on saturation current. Inductance also falls with DC bias and rises toward the self-resonant frequency, so these totals hold at low current and well below resonance. A coupled inductor with k near 1 cannot be paralleled with mismatched windings: the turns differ, the induced voltages differ, and a large current circulates between them.

Glossary

Mutual inductance (M)
The voltage induced in one coil per unit rate of change of current in the other, in henries.
Coupling coefficient (k)
M ÷ √(L1 L2): the fraction of flux shared by two coils, from 0 to 1.
Series aiding
Windings connected so their fluxes add (current enters both dotted ends). Total L1 + L2 + 2M.
Series opposing
Windings connected so their fluxes cancel. Total L1 + L2 − 2M.
Dot convention
Dots on a schematic symbol mark the winding ends that have the same polarity of induced voltage.
Leakage inductance
The inductance one winding still shows with the other shorted, L1 (1 − k²): the flux that does not couple.
DCR
DC resistance of the winding. It sets how DC current shares between parallel inductors.

Related guides

Frequently asked questions

How do you calculate inductors in series?

Add them, provided no flux from one links another: L = L1 + L2 + … So 10 µH and 22 µH in series make 32 µH. If the inductors are magnetically coupled, add or subtract 2M for each coupled pair.

How do you calculate inductors in parallel?

Add the reciprocals: 1/L = 1/L1 + 1/L2 + …, or L1 × L2 ÷ (L1 + L2) for two. 10 µH and 22 µH in parallel make 6.875 µH, less than the smaller one.

How does mutual inductance change series aiding and series opposing inductance?

It adds 2M when the fields aid and subtracts 2M when they oppose: L = L1 + L2 ± 2M. A 10 H and a 5 H coil with M = 7 H, aiding, total 29 H; opposing, only 1 H.

Can I use this as a series or parallel inductor calculator?

Yes. The Series and Parallel tabs each total up to six inductors. The Coupled pair tab adds mutual inductance for two windings.

What is the coupling coefficient k?

The fraction of one coil’s flux that links the other, from 0 (no coupling) to 1 (all of it). It sets the mutual inductance: M = k √(L1 L2). Well-shielded inductors, or ones far apart, are close to 0; a two-winding coupled inductor such as the Coilcraft MSD1260 is 0.98 or higher.

How do you measure mutual inductance?

Connect the two windings in series and measure, then reverse one winding and measure again; the Find M tab is the mutual inductance calculator for those two readings. M = (L aiding − L opposing) ÷ 4. Readings of 250 mH and 150 mH give M = 25 mH.

Why does a coupled inductor datasheet say the inductance is four times in series?

With equal windings and k close to 1, series aiding gives L + L + 2M ≈ 4L and parallel aiding gives about L. At the MSD1260’s typical k of 0.98, a 4.7 µH part gives 18.61 µH in series and 4.653 µH in parallel.

Can I put two inductors in parallel to carry more current?

Only with care. At DC the current divides by winding resistance (DCR), not by inductance, so mismatched parts share unevenly and one can saturate first. The windings of a coupled inductor are made for it: Coilcraft specifies the same inductance and half the DCR when they are paralleled.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.