NewAI Part GeneratorFree to get started
FREE TOOL

Capacitors in series and parallel calculator

The capacitors in series and parallel calculator below takes up to eight parts and gives the total capacitance, the charge and the stored energy. For a series stack, see how a voltage splits across each capacitor, the worst case with tolerance and the balancing resistor that keeps every part within its rating.

Connection
Examples
F
F

Up to 8 capacitors; the next field appears as you fill this one.

F
V

Optional: shows charge, energy and (in series) the voltage on each capacitor.

V

Optional. If they differ, enter the lowest.

%

Optional worst case. For −10/+30 % parts enter 30.

A

Optional: datasheet maximum, to size balancing resistors.

Total capacitance (series)

68.75 nF

Enter the applied voltage to see how it splits across the capacitors.

Share of the voltage on each capacitor

CapacitorValueShare
C1100 nF68.8 %
C2220 nF31.3 %

What is the formula for capacitors in series?

Use 1/C = 1/C1 + 1/C2 + … , or C1 × C2 ÷ (C1 + C2) for two. A 100 nF and a 220 nF capacitor in series make 68.75 nF, less than either one. In parallel capacitances simply add (320 nF). In series every capacitor carries the same charge, so the smallest one takes the largest share of the voltage.

Capacitors in series formula and the parallel rule

Capacitors combine the opposite way to resistors. In parallel the plate areas effectively add, so the total rises; in series the dielectric thicknesses effectively add, so it falls.

Series: 1/C = 1/C1 + 1/C2 + …     Parallel: C = C1 + C2 + …
C
total (equivalent) capacitance in F
C1, C2 …
the individual capacitances in F

For two capacitors in series, the reciprocal sum simplifies to product over sum:

C = C1 × C2 ÷ (C1 + C2)

A series string charged from 0 V puts the same charge Q on every capacitor, so the voltage on each one is inversely proportional to its capacitance:

Q = C × V     Vi = Q ÷ Ci = V × C ÷ Ci     E = ½ C V²
Q
charge on every capacitor in the string, in C
V
voltage across the whole string
Vi
voltage on capacitor i

Held at DC, leakage current takes over the split. For n capacitors rated Umax, each leaking anywhere from 0 to Ileak, equal resistors across every capacitor keep the worst one within its rating when:

R ≤ (n × Umax − U) ÷ ((n − 1) × Ileak)
U
DC voltage across the stack
Umax
highest allowed voltage on one capacitor (usually its rating)
Ileak
maximum leakage current of one capacitor

For two capacitors this is Vishay’s Rmax = (2 Umax − U) ÷ Ileak. The worst case is one capacitor that leaks nothing while the others leak the maximum; it then sits at (U + R (n − 1) Ileak) ÷ n.

Worked examples

Example 1: 1, 5 and 8 µF in series and in parallel

In series, 1/C = 1/1 + 1/5 + 1/8 = 1.325 µF⁻¹, so C = 754.7 nF, below the smallest part. In parallel the same three make 14 µF. Across 12 V the series string splits 9.057 V, 1.811 V and 1.132 V: the 1 µF capacitor takes 75.5 % of the voltage.

Example 2: two 2.7 V supercapacitors on a 5 V rail

Two 1 F cells in series make 500 mF and, matched, sit at 2.5 V each. Supercapacitors are commonly ±20 %, so one cell can be 0.8 F while the other is 1.2 F; the small one then charges to 3 V, above its 2.7 V rating. Even before leakage, a worst-case pair stays within that rating only up to 4.5 V. The pair stores 6.25 J at 5 V.

Example 3: two 470 µF 400 V electrolytics on a 700 V bus

The Vishay 193 PUR-SI 470 µF 400 V part is ±20 % with a maximum leakage of 0.01 × CR × UR = 1.88 mA after 5 minutes. In series the pair is 235 µF. While charging, a worst-case ±20 % pair puts 420 V on one capacitor, over its rating; capacitors from one batch (Vishay quotes about ±6 %) give 371 V. At DC the balancing resistor must be at most (2 × 400 − 700) ÷ 1.88 mA = 53.2 kΩ. With the E24 value 51 kΩ, the worst capacitor sits at 397.9 V, the divider draws 6.86 mA and each resistor dissipates up to 3.11 W, which is why high-voltage banks often use active balancing instead.

Two capacitors in series: common values

C1 × C2 ÷ (C1 + C2) for common ceramic values. Two equal capacitors in series give half the value.

C1 \ C210 nF22 nF47 nF100 nF220 nF470 nF1 µF
10 nF5 nF6.875 nF8.246 nF9.091 nF9.565 nF9.792 nF9.901 nF
22 nF6.875 nF11 nF14.99 nF18.03 nF20 nF21.02 nF21.53 nF
47 nF8.246 nF14.99 nF23.5 nF31.97 nF38.73 nF42.73 nF44.89 nF
100 nF9.091 nF18.03 nF31.97 nF50 nF68.75 nF82.46 nF90.91 nF
220 nF9.565 nF20 nF38.73 nF68.75 nF110 nF149.9 nF180.3 nF
470 nF9.792 nF21.02 nF42.73 nF82.46 nF149.9 nF235 nF319.7 nF
1 µF9.901 nF21.53 nF44.89 nF90.91 nF180.3 nF319.7 nF500 nF

Identical capacitors in series: share of the voltage

n equal capacitors split the voltage evenly while charging, but tolerance moves the split. The worst case puts one capacitor at the low limit and the rest at the high limit.

CapacitorsTotal CEach, matchedWorst, ±10 %Worst, ±20 %
2C ÷ 250.0 %55.0 %60.0 %
3C ÷ 333.3 %37.9 %42.9 %
4C ÷ 425.0 %28.9 %33.3 %
5C ÷ 520.0 %23.4 %27.3 %
6C ÷ 616.7 %19.6 %23.1 %

What goes wrong in real stacks

The equal-charge split only holds while the stack charges. Held at DC, the capacitor with the lower leakage current drifts up toward more than its share, which is why electrolytic and supercapacitor stacks get a resistor (or an active balancer) across each capacitor. Leakage changes with temperature and age, so size the resistor from the datasheet maximum, not a typical value. Use capacitors from the same batch in one string, and if one fails, replace the whole string. Ceramic capacitors (X5R, X7R) lose a large share of their capacitance under DC bias, so their effective value at your voltage, not the marked value, sets the split. In parallel, every capacitor sees the full voltage, and the bank behaves as the sum only at frequencies where each part’s ESR and ESL are small compared with its reactance.

Glossary

Equivalent capacitance
The single capacitor that would store the same charge at the same voltage as the whole network.
Voltage rating
The highest continuous DC voltage a capacitor is specified for, UR on electrolytic datasheets.
Leakage current
The small DC current that flows through a charged capacitor’s dielectric; Vishay specifies it after 5 minutes at rated voltage (IL5).
Balancing resistor
A resistor across each capacitor of a series stack that forces an even DC split despite unequal leakage.
Capacitance tolerance
How far a part may be from its marked value, for example ±20 % (code M) for electrolytics.
Charge (Q)
C × V, in coulombs. Every capacitor in a series string carries the same charge.

Related guides

Frequently asked questions

How do you calculate capacitors in series?

Add the reciprocals and take the reciprocal of the sum: 1/C = 1/C1 + 1/C2 + 1/C3 + … For two capacitors this is C1 × C2 ÷ (C1 + C2). The total is always smaller than the smallest capacitor in the string.

What is 100 nF and 220 nF in series?

68.75 nF. 100 × 220 ÷ (100 + 220) = 68.75 nF. In parallel the same two capacitors make 320 nF.

What is the voltage across capacitors in series?

Every capacitor in the string carries the same charge, so each takes V × Ctotal ÷ Ci: the smallest capacitor takes the largest share. With 1, 5 and 8 µF across 12 V the split is 9.057 V, 1.811 V and 1.132 V. That is the split while the stack charges; held at DC, leakage current sets it instead.

Do capacitors in series need balancing resistors?

Electrolytic and supercapacitor stacks do, because their leakage currents differ and, held at DC, the capacitor that leaks least ends up with more than its share. Vishay sizes the resistor across each of two capacitors as Rmax = (2 Umax − U) ÷ Ileak; for two 400 V, 470 µF parts on 700 V with 1.88 mA leakage that is 53.2 kΩ.

What is the formula for capacitors in parallel?

Add them: C = C1 + C2 + C3 + … Every capacitor sees the full voltage, so each one must be rated for it, and the bank’s rating is that of the lowest-rated part.

Is this a series or a parallel capacitor calculator?

Both. Pick series or parallel and enter up to eight capacitors for the total capacitance; add a voltage and you also get the charge and stored energy, plus the voltage on each capacitor in series.

Why put capacitors in series?

Mainly to reach a working voltage above one part’s rating, such as 2.7 V supercapacitor cells stacked for a 5 V rail, or 400 V electrolytics on a 700 V bus. You give up capacitance: n equal capacitors in series have 1/n of the capacitance of one.

Does a series stack store more energy?

The same capacitors store the same energy at their own voltage however they are connected. Two 1 F cells at 2.5 V each hold 3.125 J apiece; in series as 500 mF at 5 V they hold 6.25 J in total.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.