NewAI Part GeneratorFree to get started
FREE TOOL

RL time constant calculator

After a voltage step, the current through a resistor and inductor rises toward V/R at a rate set by τ = L/R. This RL time constant calculator finds τ, the inductor current over time and the time to reach a target current. Model the switch-off too, including how much faster a Zener clamp ends the current than a plain diode, and the energy the inductor stores.

Solve for
Examples
H
Ω

Series resistor plus the inductor’s DCR and the switch resistance.

V

The voltage switched across R and L.

Time constant τ = L / R

1 ms

Final current V / R
1.2 A
Initial rate of rise V / L
1.2 kA/s
Energy stored at the final current
7.2 mJ
Time to 90 % (τ ln 10)
2.303 ms
Time to 99 % (τ ln 100)
4.605 ms
5 τ (99.3 %)
5 ms
Corner frequency R / (2πL)
159.2 Hz

R is the whole loop resistance: the series resistor, the inductor’s DC resistance (DCR) and the switch. L is taken as constant: above the inductor’s saturation current its inductance drops and the current rises faster than this curve.

Current after the step
0200m400m600m800m11.201m2m3m4m5mTime (s)Current (A)63.2 %τ

Current rise in time constants

Timet / τShare of final currentCurrent
500 µs0.5 τ39.35 %472 mA
1 ms1 τ63.21 %759 mA
2 ms2 τ86.47 %1.04 A
3 ms3 τ95.02 %1.14 A
4 ms4 τ98.17 %1.18 A
5 ms5 τ99.33 %1.19 A

How to calculate RL time constants

Divide the inductance by the total resistance: τ = L / R. A 10 mH inductor with 10 Ω in series has τ = 1 ms. After a 12 V step the current heads for V / R = 1.2 A: it reaches 63.2 % (759 mA) after one τ and 99.3 % after five, following i(t) = (V / R)(1 − e^(−t/τ)).

RL time constant formulas

An inductor resists changes in its current, so after a voltage step the current climbs exponentially toward the value set by the resistance alone.

τ = L ÷ R
τ
time constant in s
L
inductance in H
R
total loop resistance in Ω, including the inductor’s DCR

After a step of V volts, starting from zero current:

i(t) = (V ÷ R) × (1 − e^(−t/τ))     vL(t) = V × e^(−t/τ)
i(t)
current at time t, in A
vL(t)
voltage across the inductance, in V

Solved for the time to reach a current i below the final value V / R:

t = τ × ln((V ÷ R) ÷ (V ÷ R − i))

When the source is removed, the current I0 decays through the resistance in its path. A clamp that holds a constant voltage Vk against the current (a diode drop, a Zener, a switch clamp) adds a term, and the current then reaches zero in a finite time. This is the result TI derives for inductive loads in SLVAE30E, where the load sees Vk = V_CLAMP − V_BAT.

i(t) = (I0 + Vk ÷ R) × e^(−t/τ) − Vk ÷ R     t0 = τ × ln(1 + I0 × R ÷ Vk)
I0
current at the moment of switch-off, in A
Vk
clamp voltage across the inductor, in V (0 for a resistor-only path)
t0
time for the current to reach zero, in s

The energy in the inductor at any current is:

E = ½ × L × i²

Worked examples

Example 1: 10 mH and 10 Ω on a 12 V step

τ = 10 mH ÷ 10 Ω = 1 ms. The current heads for 12 V ÷ 10 Ω = 1.2 A. To reach 1 A takes t = 1 ms × ln(1.2 ÷ 0.2) = 1.79 ms, and at 1.2 A the inductor stores 7.2 mJ.

Example 2: TI’s 205 mH load on a 24 V high-side switch

TI’s SLVAE30E works through a load of 205 mH and 79 Ω (its resistance at −40 °C) on 24 V. τ = 205 mH ÷ 79 Ω = 2.59 ms, the current settles at 24 V ÷ 79 Ω = 304 mA and the stored energy is 9.46 mJ. At switch-off the switch clamps at 60 V, so the load sees 60 − 24 = 36 V and the current stops after t0 = 2.59 ms × ln(1 + 304 mA × 79 Ω ÷ 36 V) = 1.33 ms. TI calculates 1.32 ms and measures about 1.3 ms.

Example 3: diode versus diode plus Zener on a coil

Take an example coil of 500 mH and 400 Ω on 12 V: τ = 1.25 ms and I0 = 30 mA. With a plain diode (Vk ≈ 700 mV) the current takes 3.62 ms to reach zero. With a 24 V Zener in series with the diode (Vk ≈ 24.7 V) it takes 495 µs, 7.3 times faster. The price: a low-side switch now sees 12 + 24.7 = 36.7 V instead of 12.7 V. For a relay, a faster current collapse means a faster release.

Current after each time constant

Every RL circuit step response has the same shape. Multiply τ by the first column to get the time.

TimeRise: share of V / RDecay (no clamp): share of I0 left
0.5 τ39.3 %60.7 %
1 τ63.2 %36.8 %
2 τ86.5 %13.5 %
2.30 τ90 %10 %
3 τ95 %4.98 %
4 τ98.2 %1.83 %
4.61 τ99 %1 %
5 τ99.3 %0.674 %

Time constant of RL circuits for common inductors and resistances

The inductor time constant is τ = L / R. Find your inductance in the first column and the total loop resistance across the top.

L \ R100 mΩ1 Ω10 Ω100 Ω1 kΩ
1 µH10 µs1 µs100 ns10 ns1 ns
10 µH100 µs10 µs1 µs100 ns10 ns
100 µH1 ms100 µs10 µs1 µs100 ns
1 mH10 ms1 ms100 µs10 µs1 µs
10 mH100 ms10 ms1 ms100 µs10 µs
100 mH1 s100 ms10 ms1 ms100 µs
1 H10 s1 s100 ms10 ms1 ms

Where the simple model stops

The formulas assume a constant inductance. Above an inductor’s saturation current (on its datasheet) the core saturates, L falls and the current shoots up faster than the curve, so check that V / R stays below it. The winding’s DCR is part of R, and it rises with temperature (TI’s example uses the −40 °C value because that gives the most current and energy). The switch adds its on-resistance while on, and at switch-off the voltage across the inductor jumps to I0 × R + Vk: a resistor-only freewheel path of 1 kΩ carrying 1 A puts 1 kV across the coil. Pick the clamp for the release time you need and a switch rated for the supply plus the clamp voltage.

Glossary

RL circuit time constant (τ)
L / R in seconds: the time for the current to reach 63.2 % of its final value after a step.
DCR
The DC resistance of an inductor’s winding, listed on its datasheet. It is part of R.
Saturation current
The current at which an inductor’s core saturates and its inductance drops by a stated amount.
Freewheeling (flyback) diode
A diode across an inductive load that carries the current when the switch opens.
Clamp voltage
The voltage a diode, Zener, TVS or switch clamp holds across the inductor while its current decays.
Demagnetization time
The time for the current in an inductive load to fall to zero after switch-off.

Related guides

Frequently asked questions

What is the time constant of an RL circuit?

τ = L / R, with L in henries and R in ohms giving seconds. 10 mH with 10 Ω gives 1 ms. After one time constant the current has reached 63.2 % of its final value V / R.

What is the formula for the current in an RL circuit?

After a step of V volts from zero current, i(t) = (V / R) × (1 − e^(−t/τ)), with τ = L / R. For 12 V, 10 mH and 10 Ω the current heads for 1.2 A and reaches 759 mA after one time constant.

How long does the current in an inductor take to reach its final value?

In theory forever, since it approaches V / R exponentially. In practice 5 τ is used: the current is at 99.3 % of its final value. It reaches 90 % after 2.3 τ and 99 % after 4.6 τ.

Why does the current in an inductor not change instantly?

The inductor's voltage is L × di/dt, so an instant change would need infinite voltage. When a step V is applied, all of it appears across the inductor at first, and the current starts rising at V / L (1.2 kA/s for 12 V across 10 mH); as the current grows, more of the voltage drops across R and the rise slows.

What happens when you switch off the current in an inductor?

The inductor keeps the current flowing and its voltage reverses to whatever it takes to find a path. Without one, that voltage climbs until something breaks down (often the switch). Give it a path: a freewheeling diode, a diode plus Zener or TVS, a resistor or an RC snubber.

Does a flyback diode slow down a relay?

Yes. With only a diode, the coil current decays through the coil's own resistance against about 0.7 V. For an example 0.5 H, 400 Ω coil on 12 V it takes 3.62 ms to reach zero; adding a 24 V Zener in series with the diode cuts that to 495 µs, at the cost of a higher voltage on the switch.

How much energy is stored in an inductor?

E = ½ L I². 10 mH carrying 1.2 A holds 7.2 mJ. That energy has to go somewhere at switch-off: into the clamp, the resistor or the switch.

Which resistance goes into the L/R time constant?

The total resistance in the current loop: any series resistor, the inductor’s DC resistance (DCR, from its datasheet), the switch on-resistance and, when the current decays, whatever is in the freewheel path. A coil driven straight from a supply has τ = L / DCR.

How is the RL time constant related to cutoff frequency?

The same R and L used as a first-order filter have a −3 dB corner at fc = R / (2πL) = 1 / (2πτ). For 10 mH and 10 Ω that is 159.2 Hz.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.