NewAI Part GeneratorFree to get started
FREE TOOL

Inductor color code calculator

This inductor color code calculator reads the bands on an axial part in microhenries, including the gold decimal-point bands of MIL-spec parts, and turns a value back into its bands. The SMD mode decodes printed codes such as 4R7, 101 and 2N2.

Mode
Start next to the wide silver MIL band. Three value bands, then the tolerance band.

Inductance

6.8 µH

±10 % · gold band as the decimal point (MIL-PRF-15305)

In µH
6.8 µH
Allowed range
6.12 µH to 7.48 µH
SMD code for this value
6R8

How do you read an inductor color code?

Read it like a resistor, but the value is in microhenries: two digit bands, a multiplier, then tolerance. Red, violet, brown, gold is 27 × 10 = 270 µH ±5 %. Below 10 µH a gold band in the first or second position is the decimal point (blue, gold, gray = 6.8 µH), and a gold third band is the ×0.1 multiplier.

How to read inductor color codes

The axial inductor color code uses the resistor colors with values in microhenries. There are two layouts for values under 10 µH, and both appear on real parts.

L = (10 × d1 + d2) × m µH
d1, d2
digit bands (black 0 to white 9)
m
multiplier band: silver ×0.01, gold ×0.1, black ×1, brown ×10, red ×100, orange ×1000
L
inductance in µH

That is the EIA layout Bourns uses on its 78F chokes. MIL-PRF-15305 coils carry a double-width silver band first, then three value bands and a tolerance band. From 10 µH up the three bands are digit, digit, multiplier as above. Below 10 µH one of the first two bands is gold and stands for the decimal point:

gold, d1, d2 → 0.d1d2 µH     d1, gold, d2 → d1.d2 µH

SMD inductor codes

Many SMD inductors, Murata and Bourns parts among them, carry a three-character code in µH, on the part where there is room and in the part number: two digits and a number of zeros (101 = 100 µH), R as the decimal point (4R7 = 4.7 µH, R47 = 0.47 µH), and for values under 0.1 µH, N as the decimal point with the value in nH (2N2 = 2.2 nH).

Not every all-digit code counts in µH. On the Coilcraft MSD1260 series the three digits count nanohenries: the MSD1260-472 is listed at 4.7 µH in its datasheet and has 472 printed on top, while the µH reading of those digits is 4.7 mH, 1000 times too high. Other parts may do the same, so for an all-digit code the calculator gives the µH reading and a warning with the nH one. Check the maker’s datasheet before trusting either.

Worked examples

Example 1: blue, gray, gold, gold (EIA)

68 × 0.1 = 6.8 µH, gold tolerance ±5 %, so between 6.46 µH and 7.14 µH. This is the example in the Bourns 78F datasheet.

Example 2: wide silver, blue, gold, gray, silver (MIL)

Skip the wide silver MIL band. Blue is 6, gold is the decimal point, gray is 8: 6.8 µH, silver ±10 % (6.12 µH to 7.48 µH). The same value as example 1, in the MIL layout from the Bourns 9310 datasheet.

Example 3: gold, red, red, silver

A gold first band puts the decimal point in front: 0.22 µH = 220 nH ±10 %. In the EIA layout the same part would be red, red, silver (22 × 0.01).

Example 4: SMD codes 4R7 and 101K

4R7 is 4.7 µH. 101K is 10 followed by one zero = 100 µH, with K = ±10 %, so 90 µH to 110 µH.

Inductor color code chart

Digit and multiplier values from MIL-PRF-15305 Table II, plus the EIA gold and silver multipliers from the Bourns 78F datasheet.

ColorDigitMultiplierTolerance
Black0×1-
Brown1×10±1 %
Red2×100±2 %
Orange3×1000±3 %
Yellow4--
Green5--
Blue6--
Violet7--
Gray8--
White9--
Golddecimal point (MIL)×0.1±5 %
Silver-×0.01±10 %
No band--±20 %

Inductor value chart: bands and SMD codes

E6 values from 0.1 µH to 1 mH, with the EIA bands, the MIL bands (after the wide silver band) and the SMD code. Tolerance band not shown.

InductanceEIA bandsMIL bandsSMD code
100 nHBrown, Black, SilverGold, Brown, BlackR10
150 nHBrown, Green, SilverGold, Brown, GreenR15
220 nHRed, Red, SilverGold, Red, RedR22
330 nHOrange, Orange, SilverGold, Orange, OrangeR33
470 nHYellow, Violet, SilverGold, Yellow, VioletR47
680 nHBlue, Gray, SilverGold, Blue, GrayR68
1 µHBrown, Black, GoldBrown, Gold, Black1R0
1.5 µHBrown, Green, GoldBrown, Gold, Green1R5
2.2 µHRed, Red, GoldRed, Gold, Red2R2
3.3 µHOrange, Orange, GoldOrange, Gold, Orange3R3
4.7 µHYellow, Violet, GoldYellow, Gold, Violet4R7
6.8 µHBlue, Gray, GoldBlue, Gold, Gray6R8
10 µHBrown, Black, BlackBrown, Black, Black100
15 µHBrown, Green, BlackBrown, Green, Black150
22 µHRed, Red, BlackRed, Red, Black220
33 µHOrange, Orange, BlackOrange, Orange, Black330
47 µHYellow, Violet, BlackYellow, Violet, Black470
68 µHBlue, Gray, BlackBlue, Gray, Black680
100 µHBrown, Black, BrownBrown, Black, Brown101
150 µHBrown, Green, BrownBrown, Green, Brown151
220 µHRed, Red, BrownRed, Red, Brown221
330 µHOrange, Orange, BrownOrange, Orange, Brown331
470 µHYellow, Violet, BrownYellow, Violet, Brown471
680 µHBlue, Gray, BrownBlue, Gray, Brown681
1 mHBrown, Black, RedBrown, Black, Red102

SMD inductor tolerance letters

LetterToleranceListed by
W±0.05 nHMurata
B±0.1 nHMurata
C±0.2 nHMurata
S±0.3 nHMurata
D±0.5 nHMurata
F±1 %Murata
G±2 %Murata
H±3 %Murata
J±5 %Murata
K±10 %Murata
M±20 %Murata, Bourns
Y±30 %Bourns

Before you trust the bands

Inductor and resistor bands use the same colors, so confirm which part you have: an ohmmeter across a color-coded inductor reads a low DC resistance, not the coded value. Read from the end the bands are bunched toward, and skip a double-width silver band. Faded gold and yellow, or brown and red, are easy to confuse on old parts, so cross-check the result against a standard E6 or E12 value. The code gives the inductance at the test frequency in the datasheet with no DC current: a ferrite-core part loses inductance as the current rises toward its saturation rating (Bourns specifies Isat as the current where inductance has dropped 30 % on the SRN6045), so check the current rating as well as the value when you replace one.

Glossary

Inductor color code
Color bands that give an axial inductor’s value in µH, using the resistor colors.
Microhenry (µH)
One millionth of a henry. Color bands and this calculator’s SMD codes read in µH; the Coilcraft MSD1260 series counts nH instead.
MIL identifier
A silver band twice the width of the others that marks a MIL-PRF-15305 RF coil.
Decimal-point band
A gold band in the first or second position of a MIL inductor, used for values under 10 µH.
EIA color code
Two digit bands, a multiplier (gold ×0.1 and silver ×0.01 included) and a tolerance band.
R notation
R as the decimal point in an SMD inductance code: 4R7 = 4.7 µH.
N notation
N as the decimal point and nH unit for values under 0.1 µH: 2N2 = 2.2 nH.

Related guides

Frequently asked questions

How do you read inductor values from the color bands?

The same way as a resistor, but in microhenries: two digit bands, a multiplier band and a tolerance band. Blue, gray, brown, silver is 68 × 10 = 680 µH ±10 %.

What does a gold band mean on an inductor?

It depends on its position. As the first or second band on a MIL-style inductor it is the decimal point (blue, gold, gray = 6.8 µH). As the third band it is the ×0.1 multiplier (blue, gray, gold = 6.8 µH), and as the last band it means ±5 % tolerance.

What is the wide silver band on an inductor?

It identifies a MIL-spec RF coil (MIL-PRF-15305): it is twice as wide as the other bands and is not part of the value. Start reading at the band next to it.

Are inductor color codes in µH or mH?

Microhenries. Brown, black, red is 10 × 100 = 1000 µH, which is 1 mH. The color code stops at orange (×1000), so the largest value is 99 mH.

How do you read an SMD inductor marking code?

Many parts use a code that counts in µH: two digits and a number of zeros (101 = 100 µH), R as the decimal point (4R7 = 4.7 µH), and N as the decimal point with the value in nH (2N2 = 2.2 nH). All-digit codes do not always count in µH: the Coilcraft MSD1260 series counts them in nH, so check the maker’s datasheet.

What does 4R7 mean on an inductor?

R is the decimal point and the unit is µH, so 4R7 is 4.7 µH. R47 is 470 nH, and a code with N, such as 2N2, is in nanohenries: 2.2 nH.

What does 101 mean on an SMD inductor?

10 followed by one zero, in µH, so a 101 inductor is 100 µH. 100 is 10 µH and 102 is 1 mH. A letter after it, as in 101K, is the tolerance (K = ±10 %).

What does 472 mean on an inductor?

It depends on the part. In the µH code used on Murata and Bourns parts it is 47 followed by two zeros, 4.7 mH. The Coilcraft MSD1260 series counts the digits in nH, so the MSD1260-472 is 4.7 µH, 1000 times lower. The maker’s datasheet settles it.

Can I tell an inductor from a resistor by its bands?

Not from the bands alone, since they use the same colors. Measure it: a 1000 µH Bourns 78F choke (brown, black, red) has at most 31.4 Ω of winding resistance, where a resistor with those bands is 1 kΩ. Very small values are harder to tell apart: the 0.1 µH part can read up to 0.06 Ω, close to the 0.1 Ω its bands would mean on a resistor.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.