NewAI Part GeneratorFree to get started
FREE TOOL

EIRP and effective radiated power calculator

An effective radiated power calculator for both EIRP and ERP: start from transmitter power, antenna gain and cable loss, and read the result in dBm and watts. Or enter a regulatory limit and get the highest conducted power that meets it.

Solve for
Examples

Conducted power at the radio or amplifier output.

Power unit

Peak gain. A chip antenna can be negative.

Gain unit
dB

Optional: free-space field strength and power flux density at this distance.

Distance unit

EIRP

22 dBm

EIRP in watts
158.5 mW
EIRP in dBW
-8 dBW
ERP
19.85 dBm EIRP − 2.15 dB
ERP in watts
96.61 mW
Transmitter power
20 dBm 100 mW
Power at the antenna
20 dBm 100 mW
Antenna gain
2 dBi -0.15 dBd

EIRP and ERP apply in the direction of the gain you entered. Use the antenna’s peak gain to compare with a regulatory limit for your band and region.

How to calculate EIRP

In dB, EIRP = transmitter power + antenna gain − cable loss. A 20 dBm radio with 1 dB of cable and a 3 dBi antenna has an EIRP of 22.00 dBm (158 mW). The ERP is 2.15 dB lower, 19.85 dBm, because it is referenced to a half-wave dipole rather than an isotropic antenna.

EIRP formula and ERP conversion

47 CFR § 2.1 defines both as the power supplied to the antenna times its gain in a given direction. They differ only in the reference antenna.

EIRP = P + G − L
ERP = EIRP − 2.15 dB
EIRP
equivalent isotropically radiated power, dBm
ERP
effective radiated power, dBm
P
transmitter output power, dBm
G
antenna gain, dBi
L
cable and connector loss, dB

The 2.15 dB is the gain of a half-wave dipole over an isotropic antenna, a linear ratio of 1.64. To find the conducted power that meets a limit, rearrange the EIRP equation:

Pmax = EIRPlimit − G + L

EIRP also sets the free-space field strength at a distance d in meters (ITU-R P.525), with p in watts:

e (V/m, r.m.s.) = √(30 × p) ÷ d

Worked examples

Example 1: a 20 dBm radio with a 3 dBi antenna and 1 dB of cable

EIRP = 20 + 3 − 1 = 22.00 dBm, which is 158 mW. ERP = 22.00 dBm − 2.15 dB = 19.85 dBm.

Example 2: the FCC 15.247 ceiling for digital modulation

1 W is 30 dBm, and with a 6 dBi antenna EIRP = 30 + 6 = 36.00 dBm (3.98 W). In free space that gives a field of 109 mV/m at 100 m.

Example 3: meeting an ERP limit of 30 dBm

An ERP limit of 30 dBm is 32.15 dBm EIRP. With a 5 dBi antenna and 1.5 dB of cable, Pmax = 32.15 − 5 + 1.5 = 28.65 dBm (733 mW) at the transmitter output.

FCC 15.247 power limits by antenna gain

Maximum conducted power and resulting EIRP for digital modulation under 47 CFR 15.247(b)(3), (b)(4) and (c)(1), ignoring cable loss. Confirm the details for your device with a test lab; other rules apply to frequency hopping systems and other bands.

Antenna gainGeneral: conductedGeneral: EIRP2.4 GHz point-to-point: conducted2.4 GHz point-to-point: EIRP5.8 GHz point-to-point: EIRP
2 dBi30.0 dBm32.0 dBm30.0 dBm32.0 dBm32.0 dBm
6 dBi30.0 dBm36.0 dBm30.0 dBm36.0 dBm36.0 dBm
9 dBi27.0 dBm36.0 dBm29.0 dBm38.0 dBm39.0 dBm
12 dBi24.0 dBm36.0 dBm28.0 dBm40.0 dBm42.0 dBm
18 dBi18.0 dBm36.0 dBm26.0 dBm44.0 dBm48.0 dBm
24 dBi12.0 dBm36.0 dBm24.0 dBm48.0 dBm54.0 dBm

EIRP, watts and ERP

Common EIRP levels with their linear power and the matching ERP.

EIRPEIRP in wattsERPERP in watts
0 dBm1 mW−2.15 dBm610 µW
10 dBm10 mW7.85 dBm6.1 mW
14 dBm25.1 mW11.85 dBm15.3 mW
20 dBm100 mW17.85 dBm61 mW
27 dBm501 mW24.85 dBm305 mW
30 dBm1 W27.85 dBm610 mW
33 dBm2 W30.85 dBm1.22 W
36 dBm3.98 W33.85 dBm2.43 W

Using EIRP against a real limit

Use the antenna's peak gain from its datasheet, and check the conditions: gain on a small ground plane or in an enclosure can differ from the published figure. Limits are specific to the band and region. In the US the FCC sets them in 47 CFR Part 15, and in Europe they are set per band through CEPT ERC Recommendation 70-03 and the ETSI harmonized standards, so read the rule for your band, including whether it is stated as EIRP or ERP, as peak or average, and whether a duty cycle applies. FCC workshop slides from October 2013 say that the ERP and EIRP guidance in KDB 412172 assumes far-field measurements and may not apply in near-field situations. Regulatory compliance is decided by testing the finished device, and this EIRP calculator only tells you where to start.

Glossary

EIRP
Equivalent isotropically radiated power: power supplied to the antenna times its gain relative to an isotropic antenna.
ERP
Effective radiated power: power supplied to the antenna times its gain relative to a half-wave dipole.
dBi
Antenna gain in dB relative to an isotropic antenna.
dBd
Antenna gain in dB relative to a half-wave dipole; dBi = dBd + 2.15.
Conducted power
Power measured at the output of the transmitter, before the cable and antenna.
dBm
Power in dB relative to 1 mW: 0 dBm = 1 mW and 30 dBm = 1 W.

Related guides

Frequently asked questions

What is EIRP?

Equivalent isotropically radiated power: the power an isotropic antenna would need to produce the same field in a given direction. It is the power supplied to the antenna times the antenna gain relative to isotropic, or in dB, EIRP = P + G − L.

EIRP vs ERP: what is the difference?

The reference antenna. EIRP is relative to an isotropic antenna and ERP is relative to a half-wave dipole, which has 2.15 dB of gain over isotropic. So ERP = EIRP − 2.15 dB for the same transmitter.

How do you convert EIRP to ERP and ERP to EIRP?

Subtract 2.15 dB to go from EIRP to ERP, and add 2.15 dB to go back. An ERP limit of 30 dBm is 32.15 dBm EIRP.

Is this an EIRP calculator or an ERP calculator?

Both. The EIRP and ERP tab shows ERP in dBm and watts next to EIRP, and the Conducted power for a limit tab accepts a limit stated as either one.

How do I convert dBd to dBi?

Add 2.15 dB: dBi = dBd + 2.15. A 0 dBd antenna is 2.15 dBi, and a 5 dBi antenna is 2.85 dBd.

What EIRP does 1 W into a 6 dBi antenna produce?

36 dBm, or 3.98 W. Under FCC 15.247, 1 W conducted with an antenna of up to 6 dBi is the limit for digital modulation in the 902 to 928, 2400 to 2483.5 and 5725 to 5850 MHz bands.

What happens under FCC 15.247 if the antenna gain is above 6 dBi?

For most systems the conducted power must drop by 1 dB for every dB of gain above 6 dBi, which holds EIRP at 36 dBm. Fixed point-to-point links get relief: at 2.4 GHz the power drops by only 1 dB for each 3 dB above 6 dBi, and at 5.8 GHz there is no reduction.

Does cable loss reduce EIRP?

Yes, dB for dB, since it reduces the power reaching the antenna. A radio at 20 dBm with 1 dB of cable into a 3 dBi antenna has an EIRP of 22.00 dBm. Check how your regulation treats cable loss when you compare to a conducted limit.

How do I convert EIRP to watts?

P(W) = 10^((EIRP in dBm − 30) ÷ 10). For example, 36 dBm is 3.98 W and 20 dBm is 100 mW.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.