NewAI Part GeneratorFree to get started
FREE TOOL

L-network impedance matching calculator

Enter a resistive source, a complex load and one frequency, and this RF impedance matching calculator returns the inductor and capacitor values of every L-section that matches them. Each solution shows its topology, Q, return-loss bandwidth and what it does with standard E24 values.

Load given as
Examples
Ω
Ω
Ω

Positive is inductive, negative is capacitive, 0 is a pure resistance.

Hz

Widest-band network

Series C 6.351 pF, shunt L 5.521 nH

Arrangement
Series at source, shunt across load
Topology
High-pass
Series reactance X
-27.39 Ω
Shunt susceptance B
-31.5 mS
Node Q
0.548 at the junction of the two parts
Loaded Q
0.274 node Q ÷ 2 when matched
10 dB return loss band
734 MHz (80%)
Input impedance check
50 + j0 Ω
Nearest E24 parts
Series C 6.2 pF, shunt L 5.6 nH
Return loss with E24 parts
34.5 dB

Parts are ideal. The band and the plot hold R constant and treat the load reactance as a fixed inductor or capacitor.

The load’s own Q (|XL| ÷ RL = 1.5) is above the node Q, which counts only the net reactance at the junction. The load sets the real bandwidth here, so read the band and the plot rather than the Q.

Return match versus frequency (|S11|)
-40-30-20-100400M600M800M1G1.2G1.4GFrequency (Hz)|S11| (dB)−10 dBf 915 MHz
1. High-pass2. Series L, shunt L3. Series L, shunt L4. Low-pass

All 4 L-sections for this load

#TopologyFrom the sourceSeries partShunt partNode Q10 dB bandE24 return loss
1High-passSeries at source, shunt across loadC 6.351 pFL 5.521 nH0.548734 MHz (80%)34.5 dB
2Series L, shunt LShunt across source, series to loadL 0.9576 nHL 7.101 nH1.22649 MHz (71%)31.6 dB
3Series L, shunt LSeries at source, shunt across loadL 4.764 nHL 11.87 nH0.548566 MHz (62%)42.3 dB
4Low-passShunt across source, series to loadL 9.479 nHC 4.261 pF1.22264 MHz (29%)25.4 dB

How to calculate an L-network for impedance matching

Compute Q = √(Rhigh ÷ Rlow − 1), then put a series reactance of Q × Rlow next to the lower resistance and a shunt reactance of Rhigh ÷ Q across the higher one. Matching 50 Ω to 10 Ω gives Q = 2, a 20 Ω series reactance and a 25 Ω shunt reactance: at 100 MHz that is 31.8 nH and 63.7 pF. A reactive load changes these values, and the calculator includes it.

Impedance matching formula for an L-network

An L-section has two degrees of freedom, enough to set both the real and imaginary parts of the input impedance. Which arrangement works, and so which impedance matching equation applies, depends on where the load sits relative to the source resistance.

When RL is above Rs (or the load’s magnitude is large enough), a shunt element goes across the load and a series element goes toward the source, as in Pozar’s equations 5.3:

B = [XL ± √(RL / Rs) × √(RL² + XL² − Rs × RL)] ÷ (RL² + XL²)    X = 1/B + XL × Rs / RL − Rs / (B × RL)
Rs
source resistance in Ω
RL, XL
load resistance and reactance in Ω
B
shunt susceptance in S (positive: capacitor; negative: inductor)
X
series reactance in Ω (positive: inductor; negative: capacitor)

When RL is below Rs, a series element goes next to the load and a shunt element goes across the source (equations 5.6):

X = ±√(RL × (Rs − RL)) − XL     B = ±√((Rs − RL) / RL) ÷ Rs

Each reactance becomes a part at the design frequency:

Series: L = X / ω or C = −1 / (ω X)    Shunt: C = B / ω or L = −1 / (ω B)

For a resistive load, the Q of the network is set by the ratio alone. The loaded Q is half of it, a relation IIIT-Delhi’s RF circuit notes state for any L-type matching network, and it follows from the source and load each contributing equal resistance at the junction when matched:

Qn = √(Rhigh / Rlow − 1)     QL = Qn / 2     Bandwidth ≈ f0 / QL

L-matching network design examples

Example 1: 200 − j100 Ω to a 100 Ω line at 500 MHz (Pozar Example 5.1)

RL is above the 100 Ω reference, so the shunt element goes at the load. The first solution has B = 2.9 mS and X = 122 Ω: Series L 39 nH, shunt C 0.923 pF. The second has B = -6.9 mS and X = -122 Ω: Series C 2.6 pF, shunt L 46.1 nH. Both give exactly 100 Ω at 500 MHz, and they differ in bandwidth away from it.

Example 2: 10 Ω to 50 Ω at 100 MHz

The load is below the source, so the series element goes next to the load. Q = √(50/10 − 1) = 2, the series reactance is 20 Ω and the shunt reactance is 25 Ω. The low-pass form is Series L 31.8 nH, shunt C 63.7 pF; the high-pass form is Series C 79.6 pF, shunt L 39.8 nH. The low-pass form holds 10 dB of return loss from 79.2 MHz to 117 MHz.

Example 3: 20 − j30 Ω to 50 Ω at 915 MHz, four solutions

RL is below Rs, and |Z|² = 1300 is above Rs × RL = 1000, so both arrangements are available:

  • High-pass: Series C 6.35 pF, shunt L 5.52 nH (series at source, shunt across load)
  • Series L, shunt L: Series L 0.958 nH, shunt L 7.1 nH (shunt across source, series to load)
  • Series L, shunt L: Series L 4.76 nH, shunt L 11.9 nH (series at source, shunt across load)
  • Low-pass: Series L 9.48 nH, shunt C 4.26 pF (shunt across source, series to load)

Q and reactances for common 50 Ω transformations

For a resistive load driven from 50 Ω. The element next to the lower resistance is the series part, and the larger the resistance step, the higher the Q and the narrower the match.

RLSeries part next toNode QLoaded QSeries |X|Shunt |X|
5 ΩLoad31.515 Ω16.7 Ω
10 ΩLoad2120 Ω25 Ω
12.5 ΩLoad1.730.86621.7 Ω28.9 Ω
25 ΩLoad10.525 Ω50 Ω
75 ΩSource0.7070.35435.4 Ω106 Ω
100 ΩSource10.550 Ω100 Ω
200 ΩSource1.730.86686.6 Ω115 Ω
300 ΩSource2.241.12112 Ω134 Ω
500 ΩSource31.5150 Ω167 Ω
1 kΩSource4.362.18218 Ω229 Ω

Low-pass L-match parts from 50 Ω

Series inductor and shunt capacitor for a resistive load, at common frequencies. Round to standard values and retune for parasitics.

Load13.56 MHz100 MHz433 MHz915 MHz2.45 GHz
10 Ω235 nH, 469 pF31.8 nH, 63.7 pF7.35 nH, 14.7 pF3.48 nH, 6.96 pF1.3 nH, 2.6 pF
25 Ω293 nH, 235 pF39.8 nH, 31.8 pF9.19 nH, 7.35 pF4.35 nH, 3.48 pF1.62 nH, 1.3 pF
100 Ω587 nH, 117 pF79.6 nH, 15.9 pF18.4 nH, 3.68 pF8.7 nH, 1.74 pF3.25 nH, 0.65 pF
200 Ω1.02 µH, 102 pF138 nH, 13.8 pF31.8 nH, 3.18 pF15.1 nH, 1.51 pF5.63 nH, 0.563 pF

What goes wrong in real matching networks

Parts are not ideal. Every inductor has a self-resonant frequency and a Q of its own, so a high-node-Q match loses more of the power in its windings: keep the node Q low unless you need the selectivity. The shunt part connects through a pad and a via, and at high frequency that adds several tenths of a nanohenry in series with it. Part tolerance matters too: on a narrow match, a 5 % part can move the center frequency out of the band. Measure the load in place if you can, since a load quoted at a different frequency or package may differ substantially, and allow a footprint for both a series and a shunt part at each end so that the network can be tuned on the board.

Glossary

L-section
A matching network of one series and one shunt reactance, forming an L shape.
Reactance (X)
The imaginary part of an impedance, in ohms: positive for an inductor, negative for a capacitor.
Susceptance (B)
The imaginary part of an admittance, in siemens: positive for a shunt capacitor, negative for a shunt inductor.
Node Q
The ratio of reactance to resistance at the junction of the matching parts.
Loaded Q
The Q of the matched circuit including the source, half the node Q for an L-section.
Return loss
How far the reflected power is below the incident power, in dB. 10 dB means 10 % of the power is reflected.
Self-resonant frequency
The frequency where a part’s parasitics cancel its intended reactance and it stops behaving as an L or C.

Related guides

Frequently asked questions

How many L-network solutions are there for one load?

Usually two or four. With the load resistance above the source, only the shunt-across-load arrangement can work, giving two sets of values; below the source, the series-to-load arrangement gives two and the shunt-across-load arrangement adds two more when |Z|² ≥ Rs × RL. A solution can lose a part or coincide with another for special loads.

What is the Q of an L-match?

Q = √(Rhigh / Rlow − 1) when the source and load are resistive. Matching 50 Ω to 10 Ω gives Q = 2. Q is fixed by the ratio, so an L-section cannot trade match for bandwidth: a pi or T network, or two L-sections in cascade, adds that freedom.

What is the difference between node Q and loaded Q?

Node Q is the reactance-to-resistance ratio at the junction between the two parts, and loaded Q is half of it when the network is matched, because source and load contribute equal resistance at that point. The half-power bandwidth is about f0 / QL: within about 15 % for a loaded Q above 2.5 and closer as Q rises, while a lower-Q match is wider and may not fall 3 dB on one side at all. A strongly reactive load stores energy the node Q does not count, so for those read the computed band instead.

Should I choose the low-pass or high-pass L-match?

Low-pass (series L, shunt C) attenuates harmonics, which suits amplifier outputs. High-pass (series C, shunt L) blocks DC in the signal path and gives a DC path to ground through the inductor, useful for feeding bias or for ESD on an antenna input. The other two combinations are also valid when the load reactance permits them.

How does the L-network calculator handle a reactive load?

The load reactance is included in the design, so the values you get are the parts to install. They already absorb or resonate that reactance at the design frequency, which is why a load can need a much smaller or larger part than its resistance alone suggests.

Can I match a load given as a resistor in parallel with a capacitor?

Yes. Choose the R ∥ C tab and enter the parallel resistance and capacitance from the datasheet. The tool converts it to R + jX at your frequency, and sweeps the parallel form for the bandwidth.

Can I use this as an antenna impedance matching calculator?

Yes, as long as the source side is resistive. Enter the antenna’s R + jX at your frequency as the load and the resistance of the line or radio port as Rs. Measure the antenna in place if you can, since a value quoted at a different frequency or on a different board may differ substantially.

Does this matching network calculator handle pi networks?

No. It solves L-sections, with one series and one shunt part. With a resistive source and load, the Q of an L-section is fixed by the resistance ratio, so when you also need to set the bandwidth, a pi or T network, or two L-sections in cascade, adds that freedom.

How accurate are the L and C values at high frequency?

They are exact for ideal parts at the design frequency. Real inductors and capacitors have self-resonance, pad capacitance and via inductance, so treat the values as a starting point above a few hundred MHz and tune on a board or in an S-parameter simulation with vendor models.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.