How to calculate slew rate and full-power bandwidth
FPBW = SR ÷ (2π × Vp), with SR in volts per second and Vp the peak output. An op amp with a 0.5 V/µs slew rate delivers a 10 V peak sine cleanly up to 7.96 kHz. Turned around, a sine needs SR ≥ 2π × f × Vp: a 20 kHz, 10 V peak audio signal needs at least 1.257 V/µs.
Op amp slew rate formula
The slew rate equation for a sine comes from its slope: Vp·sin(2πft) changes fastest at its zero crossings, where the slope is 2πf·Vp. When that slope is more than the op amp’s slew rate, the output falls behind and the sine bends into a triangle.
SR ≥ 2π × f × Vp FPBW = SR ÷ (2π × Vp) Vp,max = SR ÷ (2π × f)
- SR
- slew rate in V/s (datasheets quote V/µs; 1 V/µs = 10⁶ V/s)
- f
- signal frequency in Hz
- Vp
- peak output amplitude in V (half the peak-to-peak, √2 × RMS)
For a step of ΔV, slewing takes ΔV ÷ SR. Small steps are limited by the closed-loop bandwidth instead:
t(slew) = ΔV ÷ SR tr(10–90%) = 0.35 ÷ f−3dB slew-limited when ΔV ≥ 0.35 × SR ÷ f−3dB
- f−3dB
- closed-loop −3 dB bandwidth (GBW ÷ noise gain)
- ΔV
- output step size
The last condition is the rule from National’s Linear Brief 19. In a single-pole model the output starts to slew for any step above SR ÷ (2π f−3dB), where the linear response’s initial slope ΔV ÷ τ reaches the slew rate; the calculator models the ramp-then-exponential edge for steps in between.
Slew rate calculation examples
Example 1: a 20 kHz, 10 V peak audio output
SR = 2π × 20 kHz × 10 V = 1.257 V/µs. An LM358 (0.3 V/µs typical) can only deliver 2.39 V peak at 20 kHz, while a TL072 (20 V/µs typical) has 15.9 times the slew rate needed.
Example 2: full-power bandwidth of a µA741
With 0.5 V/µs and a 13 V peak output, FPBW = 0.5 × 10⁶ ÷ (2π × 13) = 6.12 kHz, in line with the “approximately 6 kHz” Linear Brief 19 quotes for the 741. At 10 V peak it rises to 7.96 kHz.
Example 3: a 10 V step at 20 V/µs in a 3 MHz loop
Slewing the full step takes 10 V ÷ 20 V/µs = 500 ns. The loop alone would give a 10–90% rise time of 117 ns, but any step above 2.33 V is slew-limited by the LB-19 rule (and above 1.06 V starts with a ramp), so the modeled 10–90% edge is 400 ns: the slew rate, not the bandwidth, sets it.
Slew rate needed for a sine wave
Minimum slew rate, 2π × f × Vp, in V/µs. Rows are frequency, columns the peak output amplitude.
| Frequency | 100 mV peak | 1 V peak | 5 V peak | 10 V peak |
|---|
| 1 kHz | 0.000628 V/µs | 0.00628 V/µs | 0.0314 V/µs | 0.0628 V/µs |
| 10 kHz | 0.00628 V/µs | 0.0628 V/µs | 0.314 V/µs | 0.628 V/µs |
| 20 kHz | 0.0126 V/µs | 0.126 V/µs | 0.628 V/µs | 1.26 V/µs |
| 100 kHz | 0.0628 V/µs | 0.628 V/µs | 3.14 V/µs | 6.28 V/µs |
| 1 MHz | 0.628 V/µs | 6.28 V/µs | 31.4 V/µs | 62.8 V/µs |
| 10 MHz | 6.28 V/µs | 62.8 V/µs | 314 V/µs | 628 V/µs |
Slew rate of op amps and their full-power bandwidth
Typical slew rates from each TI datasheet, at the conditions listed. The output must also be able to swing to the amplitude: an LM358 on 5 V cannot reach 10 V peak at any frequency.
| Op amp | Slew rate (typ) | FPBW at 1 V peak | FPBW at 2.5 V peak | FPBW at 10 V peak | Datasheet |
|---|
| LM358, LM358A | 0.3 V/µs (G = +1, VS = 5 V) | 47.7 kHz | 19.1 kHz | 4.77 kHz | SLOS068AB |
| LM358B | 0.5 V/µs (G = +1, 5 V to 36 V) | 79.6 kHz | 31.8 kHz | 7.96 kHz | SLOS068AB |
| µA741C | 0.5 V/µs (±15 V, RL = 2 kΩ, CL = 100 pF) | 79.6 kHz | 31.8 kHz | 7.96 kHz | SLOS094H |
| TL072 (C, I grades) | 20 V/µs (±15 V, RL = 2 kΩ, CL = 100 pF; 8 V/µs min) | 3.18 MHz | 1.27 MHz | 318 kHz | SLOS080W |
| OPA1612 | 27 V/µs (G = −1, ±2.25 V to ±18 V) | 4.3 MHz | 1.72 MHz | 430 kHz | SBOS450C |
Where the simple slew rate formula stops
The FPBW formula marks where a sine visibly turns triangular; it does not promise low distortion below that. TI’s note on FPBW and distortion shows THD rising before the classic limit, more so at higher closed-loop gain, and that op amps with slew-boost circuits can have two slew limits. Published figures vary too: the OPA1612 datasheet defines FPBW with this formula, yet lists 4 MHz at 1 Vpp where 27 V/µs gives 8.59 MHz. Design with the minimum slew rate where the datasheet gives one (8 V/µs for the TL072 against 20 V/µs typical), leave margin for distortion, and remember that capacitive loads and low supply voltages slow the output further.
Glossary
- Slew rate (SR)
- The fastest the output voltage can change, in V/µs, set by how fast internal currents can charge the compensation capacitance.
- Full-power bandwidth (FPBW)
- The highest frequency at which a sine of a given amplitude, usually the rated output swing, comes out without slew limiting.
- Slew-induced distortion
- The distortion when a sine is slew limited and turns triangular.
- Closed-loop bandwidth
- The small-signal −3 dB bandwidth of the stage, GBW ÷ noise gain for a voltage-feedback op amp.
- Rise time
- The time from 10% to 90% of a step: 0.35 ÷ f−3dB for a single pole, ΔV ÷ SR × 0.8 when slewing.
- Settling time
- The time for the output to stay within a stated error band (such as 0.01%) of its final value after a step.
Frequently asked questions
What are the slew rate and full-power bandwidth formulas?
A sine of peak Vp at frequency f changes fastest at its zero crossings, at 2π·f·Vp. The op amp must slew at least that fast: SR ≥ 2π·f·Vp. Rearranged, the full-power bandwidth is FPBW = SR ÷ (2π·Vp). A 1 V peak, 1 MHz sine needs 6.28 V/µs.
What is slew rate?
The fastest an op amp’s output voltage can change, in V/µs. It is set by how fast internal currents can charge the compensation capacitance.
How do you calculate the slew rate of an op amp from a step response?
Rearrange t(slew) = ΔV ÷ SR to SR = ΔV ÷ t: a 10 V step that slews in 500 ns is 20 V/µs. For a sine, the minimum is SR ≥ 2π·f·Vp.
What slew rate do I need for audio?
For a full 20 kHz bandwidth at 10 V peak (a large output on ±15 V rails), 1.257 V/µs; at 1 V peak, 0.1257 V/µs. An LM358’s 0.3 V/µs typical only covers 2.39 V peak at 20 kHz.
What is the full-power bandwidth of a 741?
With its 0.5 V/µs typical slew rate, 7.96 kHz at 10 V peak and 6.12 kHz at 13 V peak. Above that a full-swing sine turns into a triangle.
What happens when an op amp is slew-rate limited?
The output can no longer follow the input: a sine turns into a triangle with a smaller amplitude and a phase lag, and slew rate distortion rises sharply. The feedback loop is effectively open while the output slews, so the circuit stops behaving like its small-signal model.
Is slew rate the same as bandwidth?
No. Bandwidth (GBW ÷ noise gain) limits small signals and does not depend on amplitude; slew rate limits large signals and does. A stage can have plenty of bandwidth for a 10 mV signal and still distort a 10 V one at the same frequency.
How long does an op amp take to respond to a step?
About ΔV ÷ SR for a large step: 10 V at 20 V/µs takes 500 ns. A small step does not slew at all; its 10–90% rise time is 0.35 ÷ f−3dB, set by the closed-loop bandwidth. In a 3 MHz loop the crossover is around 2.33 V (LB-19 rule), and steps above 1.06 V start with a short ramp.
Does slew rate change with supply voltage, load or gain?
Yes, somewhat. Datasheets specify slew rate at one supply, load and gain (for example G = +1, CL = 100 pF), and capacitive loads in particular can slow it. Rising and falling edges can also differ. Use the minimum value in this op amp slew rate calculator when the design depends on it.
More free PCB tools
See all free electronics tools →
- RC high pass filter calculatorCutoff frequency of an RC high-pass filter, or R or C for a cutoff, with the Bode plot and standard values.
- Op amp gain calculatorGain and resistor values for inverting, non-inverting, difference and summing op amp circuits, with bandwidth from GBW.
- Sallen-Key filter calculatorComponent values for a unity-gain Sallen-Key low-pass or high-pass filter with Butterworth, Bessel or Chebyshev response.
- RLC circuit calculatorResonant frequency, Q, bandwidth and damping of series or parallel RLC circuits, with the impedance curve.
- Johnson noise calculator (resistor thermal noise)Johnson-Nyquist noise voltage and current of a resistor for a bandwidth and temperature, in nV/√Hz, µVrms and dBm.
- RC filter calculator (low pass)Cutoff frequency of an RC low-pass filter, or R or C for a cutoff, with the Bode plot and standard part values.
Design the whole board, not one number
ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.