NewAI Part GeneratorFree to get started
FREE TOOL

Gain bandwidth product calculator

With this gain bandwidth product calculator you can find the closed-loop bandwidth of an op amp stage from its GBW and noise gain, the GBW you need for a gain and bandwidth, and how much bandwidth splitting the gain over cascaded stages buys. It uses the single-pole op amp model from TI’s application notes and says where that model stops being accurate.

Solve for
Examples
Configuration
V/V

Magnitude of the signal gain: 10 for a gain of −10.

Hz
dB

Optional, from the data sheet. Blank treats it as very large.

Hz

Optional: gain drop and phase lag at this frequency.

Closed-loop bandwidth (−3 dB)

100 kHz

Noise gain 1/β
10 V/V equals the signal gain
Rise time (10–90 %)
3.497 µs
Gain within 0.1 dB up to
15.26 kHz
Gain within 1 % up to
14.25 kHz

Single-pole model of a voltage-feedback op amp. Real parts have more poles near GBW, so the response can peak and the measured −3 dB point often lands somewhat above GBW/NG (TI’s own TLV170 simulation at a noise gain of 3 shows 519 kHz against 400 kHz calculated).

Open-loop and closed-loop gain
-40-200204060801001k10k100k1M10MFrequency (Hz)Gain (dB)0 dBf−3dB 100 kHz
Op amp open-loop gainClosed-loop gain

How do you calculate bandwidth from gain bandwidth product?

Divide the op amp’s GBW by the noise gain of the circuit: f−3dB = GBW ÷ NG. For a non-inverting amplifier the noise gain equals the gain; for an inverting one it is 1 + R2/R1. An LM358B with a GBW of 1.2 MHz at a gain of 10 has a bandwidth of 120 kHz.

Gain bandwidth product formula

A voltage-feedback op amp is compensated with one dominant pole, so above a few hertz its open-loop gain falls at 20 dB per decade and gain times frequency is constant. Feedback trades that gain for bandwidth: the closed loop rolls off where the open-loop gain meets the noise gain.

f−3dB = GBW ÷ NG
f−3dB
closed-loop −3 dB bandwidth in Hz
GBW
gain bandwidth product of the op amp in Hz
NG
noise gain: G for a non-inverting stage, 1 + R2/R1 for an inverting one

With a finite open-loop DC gain A0 the exact single-pole gain bandwidth formula adds a small term, and the DC gain falls short of the ideal by 1 / (1 + A0/NG):

f−3dB = GBW ÷ NG + GBW ÷ A0

The gain is down 3 dB at f−3dB but already falling well below it. To stay within a droop of D dB at a frequency f, and for n identical stages in cascade (each one a single pole at fc):

f−3dB ≥ f ÷ √(10^(D/10) − 1)     f−3dB,total = fc × √(2^(1/n) − 1)

Gain bandwidth product examples

Example 1: LM358B at a gain of 10

The LM358B’s typical GBW is 1.2 MHz. A non-inverting gain of 10 has a noise gain of 10, so f−3dB = 1.2 MHz ÷ 10 = 120 kHz. The gain is within 0.1 dB only up to 18.3 kHz, and the small-signal rise time is 2.91 µs.

Example 2: 40 dB of audio gain, flat to 0.1 dB at 20 kHz

For a 0.1 dB droop at 20 kHz the closed loop needs f−3dB ≥ 20 kHz ÷ √(10^0.01 − 1) = 131 kHz. At 100 V/V that is a GBW of 13.1 MHz. Two stages of 10 V/V can each droop 0.05 dB, so each needs 186 kHz and a GBW of only 1.86 MHz.

Example 3: 1000 V/V on an OPA2210, one, two or three stages

One stage: 18 MHz ÷ 1000 = 18 kHz. Two stages of 31.6 V/V each reach 569 kHz, and the pair is down 3 dB at 569 kHz × 0.6436 = 366 kHz (TI’s simulation in SBOA356 shows 364 kHz). Three stages of 10 V/V give 918 kHz.

Gain bandwidth product of op amps: bandwidth at gains of 2, 10 and 100

Typical GBW from each data sheet at 25 °C, and GBW ÷ NG for a non-inverting stage. Data sheets give GBW as a typical value; it varies with supply, temperature and part.

Op ampGBW (typ)Gain 2Gain 10Gain 100Note
TLV1701.2 MHz600 kHz120 kHz12 kHzTI SBOA270
LM358B / LM358BA1.2 MHz600 kHz120 kHz12 kHzLM358 and LM358A: 0.7 MHz
TL072 (most packages, TL07xH)5.25 MHz2.63 MHz525 kHz52.5 kHzNS, PS packages and TL07xM: 3 MHz
OPA221018 MHz9 MHz1.8 MHz180 kHz
OPA161240 MHz20 MHz4 MHz400 kHzSpecified at G = 1; 80 MHz at G = 100

Cascaded stage bandwidth shrink factor

n identical, buffered single-pole stages are 3 dB down at fc × √(2^(1/n) − 1). The last column is TI’s root-sum-square estimate, fc / √n, which reads high.

Stages nShrink factorEach stage down at total f−3dBfc / √n estimate
11.0000−3.01 dB1.0000
20.6436−1.51 dB0.7071
30.5098−1.00 dB0.5774
40.4350−0.75 dB0.5000
50.3856−0.60 dB0.4472
60.3499−0.50 dB0.4082

Where the simple formula stops working

GBW ÷ NG assumes one dominant pole. Real op amps have more poles near GBW, so at low noise gains the response peaks and the measured bandwidth can be higher than calculated: TI’s TLV170 simulation at a noise gain of 3 shows 519 kHz against the 400 kHz the formula gives. Capacitive loads and stray capacitance at the inverting input add phase lag and peaking too. Current-feedback amplifiers do not have a constant GBW at all; their bandwidth is set by the feedback resistor. Decompensated parts quote GBW at a high gain and are stable only above a minimum noise gain, so never use one below it. GBW on a data sheet is a typical figure, which is why the GBW needed tab also shows the value with a design margin (2× unless you change it). Finally, GBW is a small-signal figure: check the slew rate for the full output swing.

Glossary

Gain bandwidth product (GBW, GBP)
Open-loop gain times frequency where the open-loop gain falls at 20 dB per decade; constant for a single-pole op amp.
Noise gain (1/β)
The gain from a voltage source at the non-inverting input to the output: 1 + R2/R1 for both inverting and non-inverting stages.
Closed-loop bandwidth
The −3 dB frequency of the amplifier with feedback, GBW divided by the noise gain.
Dominant pole
The low-frequency pole an op amp is compensated with, which makes the open-loop gain fall at 20 dB per decade.
Decompensated op amp
An op amp compensated for more bandwidth that is only stable above a minimum noise gain.
Full-power bandwidth
The highest frequency of a full-swing sine before the slew rate distorts it: SR ÷ (2π Vpeak).

Related guides

Frequently asked questions

What is gain bandwidth product in an op amp?

It is the product of the open-loop gain and frequency in the region where the open-loop gain falls at 20 dB per decade, so it is constant there. For a single-pole op amp it equals the unity-gain frequency, and it is listed in the data sheet as GBW or GBP, usually as a typical value.

What is the op amp bandwidth formula?

Divide the GBW by the noise gain: f−3dB = GBW ÷ NG. An LM358B (1.2 MHz typical) at a non-inverting gain of 10 gives 120 kHz. The result is a small-signal bandwidth; large output swings are also limited by slew rate.

How do you calculate the gain bandwidth product a design needs?

Multiply the noise gain by the closed-loop bandwidth you need: GBW = NG × f−3dB. For 100 V/V and 131 kHz that is 13.1 MHz. Data sheets give GBW as a typical value, so the GBW needed tab also shows it with a design margin (2× unless you change it).

What is the unit of gain bandwidth product?

Hertz, usually quoted in MHz. Gain is a ratio (V/V), so gain times frequency comes out in Hz.

Why does an inverting amplifier have less bandwidth than its gain suggests?

Bandwidth follows the noise gain, which for an inverting stage is 1 + R2/R1, one more than the signal gain. TI’s TLV170 example at a gain of −2 has a noise gain of 3 and a bandwidth of 400 kHz, the same as a non-inverting gain of +3.

What GBW do I need for an audio preamp?

For 40 dB (100 V/V) flat to 0.1 dB at 20 kHz in one stage, the closed loop needs 131 kHz of bandwidth, so GBW ≥ 13.1 MHz. Splitting the gain into two stages of 10 V/V needs only 1.86 MHz per op amp.

Does cascading two op amp stages increase bandwidth?

Yes, when the gain is high. TI’s OPA2210 example at 1000 V/V reaches 18 kHz in one stage and 366 kHz as two stages of 31.6 V/V. The chain is narrower than each stage by √(2^(1/n) − 1), 0.644 for two stages.

Is GBW the same as unity-gain bandwidth?

For an op amp with one dominant pole they are nearly equal, and many data sheets use the terms interchangeably. They differ when a second pole sits near crossover, and decompensated op amps quote GBW at a high gain because they are not stable at unity gain.

What is the difference between GBW and full-power bandwidth?

GBW sets the small-signal bandwidth. A large output sine is limited by slew rate, to SR ÷ (2π Vpeak): the TLV170’s 0.4 V/µs supports a 14 V peak sine only up to 4.55 kHz, even though its small-signal bandwidth at a gain of −2 is 400 kHz.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.