NewAI Part GeneratorFree to get started
FREE TOOL

Fresnel zone calculator

Enter a frequency and path length and this Fresnel zone calculator gives the radius of the first zone at any point on a radio link and the clearance it needs. It adds earth bulge and any obstacle height to give the antenna height that keeps the path clear.

Radius at
Examples
Hz
km
% of first zone

60 % is the ITU-R limit of the free-space region.

m

Trees, buildings or terrain above the datum.

m

Optional: solves for the height of antenna B.

Clearance always uses the first zone.

First Fresnel zone radius

12.5 m

at the midpoint

60 % of the first zone
7.497 m
Earth bulge at this point
0.3679 m k = 1.333
Antenna height, both ends equal
7.865 m obstacle + bulge + clearance
Wavelength
124.9 mm
Knife-edge loss at this clearance
0 dB ν = −0.85

Heights are measured from one level datum, as if both ends and the obstacle stood at the same ground elevation. Add terrain elevation for a real path.

Ray, first Fresnel zone and Earth surface along the path
-50510152025012345Distance from A (km)Height (m)2.50 km
RayFirst zone, upperFirst zone, lower60 % boundaryEarth surface

First zone along this path

Distance from ARadius60 % clearanceEarth bulgeRay height needed
0.500 km7.5 m4.5 m132 mm4.63 m
1.00 km10 m6 m235 mm6.23 m
1.50 km11.5 m6.87 m309 mm7.18 m
2.00 km12.2 m7.35 m353 mm7.7 m
2.50 km12.5 m7.5 m368 mm7.87 m

How do you calculate the first Fresnel zone radius?

Use R1 = √(λ d1 d2 ÷ (d1 + d2)). At the midpoint of a 5 km link at 2.4 GHz, λ is 12.5 cm and R1 = 12.5 m. Keep at least 60 % of that, 7.5 m, clear of obstacles, and add the earth bulge at that point (368 mm here) when you set the antenna height.

Fresnel zone formula

ITU-R P.526 defines Fresnel ellipsoids as the surfaces where the path through a point is longer than the direct ray by nλ/2. Their radius at a point along the path comes from the Fresnel zone equation:

Rn = √( n × λ × d1 × d2 ÷ (d1 + d2) )
Rn
radius of zone n, in m
n
zone number, 1 for the first zone
λ
wavelength, c ÷ f, in m
d1, d2
distance from the point to each end, in m

The formula assumes d1 and d2 are much longer than the wavelength. The surface of the Earth rises above the straight line between the two ends by the earth bulge, using an effective radius of k × 6371 km:

h = d1 × d2 ÷ (2 × k × R)
h
earth bulge in m
k
effective Earth radius factor, about 4/3 at the median
R
Earth radius, 6371 km

With both antennas at the same height, the height that clears an obstacle at this point is:

antenna height = obstacle + h + 0.6 × R1

Fresnel zone calculation examples

Example 1: 2.4 GHz over 5 km, open ground

At the midpoint, R1 = √(0.1249 × 2500 × 2500 ÷ 5000) = 12.5 m. 60 % clearance is 7.5 m and the earth bulge at k = 4/3 is 368 mm, so two equal antennas need to be about 7.87 m high.

Example 2: 915 MHz over 15 km with 10 m trees at the midpoint

R1 = 35.1 m, so 60 % is 21 m, and the earth bulge is 3.31 m. Adding the 10 m trees gives an antenna height of 34.3 m at both ends. A lower frequency makes the zone wider, so the clearance term dominates here.

Example 3: 6 GHz over 50 km in the worst month

R1 = 25 m. ITU-R P.530 gives ke = 157 ÷ (144 + 2670 ÷ 50) = 0.795, for an earth bulge of 61.7 m at the midpoint, against 36.8 m at the median k of 4/3.

First Fresnel zone radius at the midpoint

Radius in meters at the middle of the path, the widest point. Take 60 % of a value for the usual clearance target.

Path433 MHz868 MHz915 MHz2.4 GHz5.8 GHz24 GHz
1 km13.2 m9.29 m9.05 m5.59 m3.59 m1.77 m
2 km18.6 m13.1 m12.8 m7.9 m5.08 m2.5 m
5 km29.4 m20.8 m20.2 m12.5 m8.04 m3.95 m
10 km41.6 m29.4 m28.6 m17.7 m11.4 m5.59 m
20 km58.8 m41.6 m40.5 m25 m16.1 m7.9 m
50 km93 m65.7 m64 m39.5 m25.4 m12.5 m

Earth bulge at the midpoint

Height of the Earth above the straight line between the two ends. Earth bulge does not depend on frequency.

Pathk = 4/3 (median)k = 1k = 2/3
1 km14.7 mm19.6 mm29.4 mm
5 km368 mm491 mm736 mm
10 km1.47 m1.96 m2.94 m
20 km5.89 m7.85 m11.8 m
30 km13.2 m17.7 m26.5 m
50 km36.8 m49.1 m73.6 m
80 km94.2 m126 m188 m

Using these numbers on a real path

These results assume flat ground at one datum. A real survey adds terrain elevation at each end and at each obstacle, and the tallest point in the ray’s way sets the height, which is often not the midpoint. Use the Any point tab for it. Above about 13 GHz, ITU-R P.530 warns that the obstacle height estimate begins to approach the zone radius, so add that uncertainty to the clearance. Trees grow and leaves absorb, so leave margin above vegetation. For long microwave links, P.530 recommends checking the antenna heights at both the median k and the worst-month ke, and using the taller result.

Glossary

Fresnel zone
An ellipsoidal region around the direct ray, defined by paths that are multiples of λ/2 longer than the ray.
First Fresnel zone
The innermost ellipsoid (n = 1), which carries most of the energy of the link.
Earth bulge
The height of the curved surface of the Earth above the straight line joining the two ends of the path.
k factor
The ratio of the effective Earth radius to the true radius, used to model atmospheric refraction.
Knife-edge diffraction
The loss caused by a sharp obstacle near or in the ray, predicted from the parameter ν.
Line of sight
A path where the direct ray clears the terrain and no obstacle enters the first Fresnel zone.

Related guides

Frequently asked questions

What is a Fresnel zone?

An ellipsoidal region around the direct ray between two antennas, defined by paths that are multiples of λ/2 longer than the ray. The first zone, the innermost one, carries most of the energy of the link, so Fresnel zone clearance usually refers to that one.

What is the Fresnel zone formula?

Rn = √(n λ d1 d2 ÷ (d1 + d2)), where λ is the wavelength and d1 and d2 are the distances from the point to the two antennas, in the same units. It is largest at the midpoint, where it becomes ½ √(n λ d). The first Fresnel zone formula is the same with n = 1.

Why is 60 % of the first Fresnel zone the usual clearance target?

ITU-R P.526 places the edge of the diffraction zone at a clearance of 60 % of the first zone radius. At that clearance the knife-edge parameter is ν = −0.85, past the −0.78 limit of the ITU loss formula, so the loss is effectively zero. A ray that just grazes an obstacle loses about 6 dB.

How big is the Fresnel zone at 2.4 GHz over 5 km?

12.5 m radius at the midpoint, so 60 % clearance is 7.5 m. The zone is a radius around the ray, so that clearance is measured from the ray down to the top of the obstacle.

How do you calculate earth bulge?

h = d1 d2 ÷ (2 k R), with R = 6371 km and k about 4/3 for a standard atmosphere. At the middle of a 10 km path that is 1.47 m.

What k factor should I use?

ITU-R P.530 gives a median of about 4/3 and advises using it when you have no local data. For the worst month in a continental temperate climate it gives ke = 157 ÷ (144 + 2670 ÷ d), about 0.80 on a 50 km path, which bends the ray less and makes the earth bulge larger.

Does a higher frequency need less clearance?

Yes. The radius scales with the square root of the wavelength: over 10 km the midpoint radius is 28.6 m at 915 MHz and 11.4 m at 5.8 GHz. Earth bulge does not depend on frequency.

Do I need to clear the whole first Fresnel zone?

For free-space propagation, 60 % of the first zone is the usual minimum, and ITU-R P.530 uses 100 % of it at the median k when sizing antenna heights on microwave links. Below about 2 GHz it notes that smaller fractions may be necessary to avoid unacceptably large antenna heights.

More free PCB tools

See all free electronics tools →

Sources

Design the whole board, not one number

ProtoFlow is free AI PCB design software: describe a circuit and get a schematic with real parts, PCB layout with an autorouter, SPICE simulation and Gerber files. Native KiCad, Altium and EAGLE import and export. Free on macOS, Windows and Linux.

Get for Mac

Free to start. No card required.